1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Speaker grill ribs
Tgace459
Member
***
Posts: 130
Threads: 25
Joined: Apr 2016
City: Buffalo NY
#1

04-25-2017, 03:44 PM
I have done cabinets where I decided to remove the ribs of the speaker gill on consoles where it was a simple as removing some screws and loosening small dabs of glue. They turned out pretty well and I didn't have to scrape out all the nooks and crannies when stripping. Whats the general consensus on doing that?

To each his own? or am I courting some sort of disaster when I do that? I have a 37-650 I'm planning on starting to strip tonight and am considering removing the speaker ribs/bars....
(This post was last modified: 04-25-2017, 03:45 PM by Tgace459.)
Find
Arran
Phorum Expert
*****
Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

04-27-2017, 11:31 PM
Test it on one bar, if you undo the screws and it doesn't come off with light finger pressure don't force it.
Regards
Arran
Find
Fred Taylor
Phorum Expert
*****
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
#3

05-20-2017, 09:21 AM
Yes, remove the bars and refinish separate.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 3010 online users. [Complete List]
» 1 Member(s) | 3009 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration