Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric Old and New
#1

I mentioned I got a GE AA5 from a pal at work, cabinet is cleaned up, epoxiied inside and about done. The numberson the dial are fragile and I am not going to clean in that spot anymore not to rub them off. No model number and I have not found it in an archive yet.

On another GE note featured are 2 probably early eighties models recently found on the bay. Rare for me to go there and rarer to buy. I needed a better portable and this looked clean and the little table set fits on my small kitchen table. Both are surprisingly sensitive and sound pretty good. The portable is a good AM Dxer at nite.
Total for both less than 25.00. So by most standards not very vintage but by 2017 standards very vintage. Table set #7-4115B portable #7-2857A

Chassis GE pics added now.

https://www.flickr.com/photos/92577012@N...1360369981

Here is the Delmonico I mentioned...
https://www.flickr.com/photos/92577012@N...0376229113

Paul

Tubetalk1
#2

Hey, ANY analog radio today IS vintage.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Don't know why, but I have always liked those Delmonico radios.  I think it must be the odd ball name and dual speakers, how does it sound Paul?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

have not played it yet, a bit leary. Need to see the underside of the chassis. The fellow who owned it had put tape on the dial where his fave statios were, tried some goo gone and a razor but need to be very careful getting the gunk off.

Will let you know. 

I always liked Delmonico potatoes!

paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM

[-]
Who's Online
There are currently 4696 online users. [Complete List]
» 2 Member(s) | 4694 Guest(s)
AvatarAvatar

>