Please ID this Silvertone
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Please ID Cannot find any info or schematic on this..
[Image:
https://farm5.staticflickr.com/4050/3490...f0b0_b.jpg ]
Thanks
Skip...
(This post was last modified: 09-22-2017, 10:57 PM by
vecher .)
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Sears Silvertone 1764 in riders 4-3
It is the only one with a 1v tube in the lineup.
See link
http://www.grillecloth.com/sylvania/tube...ubmit&db=3
Riders 4-3
http://www.americanradiohistory.com/Arch...34-STU.pdf
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
(This post was last modified: 05-23-2017, 12:15 AM by
OldRestorer .)
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Thanks Kirk... Was in Joe's shed.. Got it for 10.00
Also got a Heathkit IT-11 Cap tester for 15.00
My heathkit C-3 is not working..
Skip...
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hope your resistance line cord is good! If not you'll need to scare up a 7.4mf non polarized cap to drop the heater voltage.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
Nice little depression set Skip!
(05-23-2017, 07:39 AM) Radioroslyn Wrote: Hope your resistance line cord is good! ......
What are the odds of that? We used to find them N.I.B. and you could hear them crack as you tried to straighten them out
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I think I have still have a few of them around some where. Got to preheat them to avoid the crackels.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
boy that shed is never ending
sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Geeze,
I better get back there before you clean it out Skip,
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Just what you need some more curtain burners!!!!!![Image:
http://philcoradio.com/phorum/images/smi...on_eek.gif ]
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Yup Every time I go in there I find something Different I had not seen before..
Skip...
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Where do I find a 7.4uf Cap?
Skip...
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
8uf will work,,,,can,,, I ,,have a hall pass to the Shed,,,,I can help clean it out ,,,lololol,,,
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
I will check with Joe He is the one doing this for a friend..
I will let everyone know if he has another open house per say.. He is a good friend and its only about 10 minutes from me..
Skip..
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hey Skip,
Insteadi of finding a 7.4 non polarize cap you could use a 140 ohm resistor @20w or better, and 1N4007.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Terry, I heard that Diodes seem to fail a lot..Maybe that's not true.. Could you draw where in the circuit they should go?
Skip...
Users browsing this thread: 6 Guest(s)
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,
Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many.
Take care and BE HEALTHY! Gary
P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire.
The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members,
Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind.
Check any soldered, riveted ground conne...Chas — 01:24 PM
Who's Online
There are currently 6234 online users. [Complete List ]» 1 Member(s) | 6233 Guest(s)