Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Got another Mdl 600/Guess what's bad!
#1

The oscillator coil. Still no knobs either. Time to break out the #36 wire and have some fun! This one is an earlier version. Less louvers on the top of the cabinet and no ridges on the tuning cap for the pointer.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

At this rate, you're going to become an expert on the 600! Icon_lol

--
Ron Ramirez
Ferdinand IN
#3

Well I guess that will be my big claim to fame!! I think I already know too much about them.The dollar pocket watches seems the be a nice reprieve from radios and the like. Anyway my daily watcher B/W TV when up in smoke the other night. It went ZORCH and the screen went black. After taking a good look at it the filament winding for the damp tube arced over to the chaiss. Lots of HV on it. So it's getting it's own transformer. Maybe today.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1944 online users. [Complete List]
» 3 Member(s) | 1941 Guest(s)
AvatarAvatarAvatar

>