Please ID this Silvertone
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Please ID Cannot find any info or schematic on this..
[Image:
https://farm5.staticflickr.com/4050/3490...f0b0_b.jpg ]
Thanks
Skip...
(This post was last modified: 09-22-2017, 09:57 PM by
vecher .)
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
Sears Silvertone 1764 in riders 4-3
It is the only one with a 1v tube in the lineup.
See link
http://www.grillecloth.com/sylvania/tube...ubmit&db=3
Riders 4-3
http://www.americanradiohistory.com/Arch...34-STU.pdf
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
(This post was last modified: 05-22-2017, 11:15 PM by
OldRestorer .)
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Thanks Kirk... Was in Joe's shed.. Got it for 10.00
Also got a Heathkit IT-11 Cap tester for 15.00
My heathkit C-3 is not working..
Skip...
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Hope your resistance line cord is good! If not you'll need to scare up a 7.4mf non polarized cap to drop the heater voltage.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 3,122
Threads: 57
Joined: Apr 2011
City: Lexington, KY
Nice little depression set Skip!
(05-23-2017, 06:39 AM) Radioroslyn Wrote: Hope your resistance line cord is good! ......
What are the odds of that? We used to find them N.I.B. and you could hear them crack as you tried to straighten them out
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
I think I have still have a few of them around some where. Got to preheat them to avoid the crackels.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
boy that shed is never ending
sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
Geeze,
I better get back there before you clean it out Skip,
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Just what you need some more curtain burners!!!!!![Image:
http://philcoradio.com/phorum/images/smi...on_eek.gif ]
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Yup Every time I go in there I find something Different I had not seen before..
Skip...
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Where do I find a 7.4uf Cap?
Skip...
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
8uf will work,,,,can,,, I ,,have a hall pass to the Shed,,,,I can help clean it out ,,,lololol,,,
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
I will check with Joe He is the one doing this for a friend..
I will let everyone know if he has another open house per say.. He is a good friend and its only about 10 minutes from me..
Skip..
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Hey Skip,
Insteadi of finding a 7.4 non polarize cap you could use a 140 ohm resistor @20w or better, and 1N4007.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Terry, I heard that Diodes seem to fail a lot..Maybe that's not true.. Could you draw where in the circuit they should go?
Skip...
Users browsing this thread: 1 Guest(s)
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
Who's Online
There are currently no members online.