Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Fellow Philco Phans 
I'd appreciate some help.
I just picked up this 1936 620F, and it has been worked on. Most noticeably, the grill cloth  . I plan to replace it, but the backing is a flimsy cardboard. 
Would anyone happen to have this or a similar model that would be so kind as to get a tracing or a good quality pic of the original grill board for me 
[Image: https://farm5.staticflickr.com/4207/3554...6d9c_k.jpg]
[Image: https://farm5.staticflickr.com/4257/3484...4c3a_k.jpg]
Thanks in advance!
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
Not sure if this will help at all, as it's a model 625, which may or may not have the same backing board, but this reassembly video shows how it looks beginning at around the 6:40 mark:
https://www.youtube.com/watch?v=tCkg_QaDCno
Greg V.
West Bend, WI
Member WARCI.org
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
This will do! Thank you very much! 
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
One more Question: I'm in the process of recapping, and need to know the values of the tone control. Part No. 30-4316.
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Looks like 0.02 or could be 0.01 kind of hard to tell. and 3 or 5000 uuf. 61 & 61a on schematic.
http://www.nostalgiaair.org/pagesbymodel...013804.pdf
(This post was last modified: 07-03-2017, 09:54 PM by KCMike.)
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
It's a bit clearer on this scan of service bulletin 218A:
https://drive.google.com/file/d/0B64cfWa...sp=sharing
0.02uF in the tone control for 61.
0.003uF tubular for 61a.
BTW - nice radio Jeff!
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Thanks Nathan!
Hopefully this 620 will go smoother than my 1st!
Took me 13 months to get my 1st up and running. 
So far it's going well.
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I made this video a couple nights ago. It's up and running.  I have a reproduction dial on order from Radio Daze, and a grill cloth from Richmond Designs . I'll wait until I get the dial in before doing the alignment, as the one on there now is incorrect. 
[Video: https://youtu.be/vzbKkz7eZyc]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Shadow Meter Bulb
|
| Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM |
|
Shadow Meter Bulb
|
| Ok. Thanks for the correction.RossH — 03:09 PM |
|
Model 28L
|
| For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM |
|
37-60 revision 6
|
| I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM |
|
Shadow Meter Bulb
|
| Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM |
|
Hickok AC51 tube tester
|
| Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
|
Model 28L
|
| Hello,
I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020.
Can...HORSTE — 10:32 AM |
|
Philco 42-1008 conversion kit
|
| I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM |
|
HiFi (Chifi) tube amp build - but my own design.
|
| Tim
Well...a chassis is metal. Magnetic or not, it does not matter.
A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM |
|
Hickok AC51 tube tester
|
| I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM |
|
Who's Online
|
There are currently 3380 online users. [Complete List]
» 1 Member(s) | 3379 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
