Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

High concentration of radios in North/Northeast
#1

I have noticed an unusually large concentration of vintage radios for sale in the North and Northeast. I seldom see any in the South. What can account for this skewed distribution of Philco radios?
as always
Garrett Meadows
#2

I have alway thought this too... I have had a lot of conversations with collectors on this subject... Many of them, and I believe it myself, was population and wealth... Also most of the radio manufacturers where in the eastern half of the country... Take Philco, they where out of Philadelphia... RCA, they where out of New Jersey... Zenith, they where out of Chicago.. There was a lot higher population and wealth in the north eastern part of the country at the times these radios where built.... most of those radios have stayed in that area for the last 70+ years, and are now coming up for sale... I live out in South Dakota and there are barely any high end radios here... Back then there was little to no population here and no one could afford most radios... Plus most of the farms here didnt even get modern electricity until the late 40's into the 50's... Most of what you see here are farm radios(battery powered) and for some reason a lot of Silvertones... Most likely due to the Sears & Roebuck catalogs and that they too where located in Chicago... The last couple radios I bought where a Zenith 15U269 and a pair of 38-690's... I had to drive 21 hours round trip to get them because those types of radios just never made it this far west... And from what it sounds like, the South too... It seems to me that all the money was in the Northeast at the time and that is where the radio manufacturers where located, so thats where all the radios ended up...
#3

I had a similar train of thought: concentration of wealth, proliferation of manufacturers, etc. From the 1920s to as late as the 1950s, the majority of the south was still undeveloped and poor. Like you, I've resigned myself to harsh reality that if I am ever going to own the kind of console Philco radio I want, I'm going to have to drive perhaps a 1000 miles. I can fully appreciate driving 21 hours round trip. I live in Baton Rouge, Louisiana, and there was a guy in Houston whose father died and left behind some Philco radios he was selling. Before I could could get away to drive to Houston, the radios were snapped up. There was a guy in Vermont who had the exact console Philco I wanted. I was going to send him the money to pay for the radio and hold it until I could find some way to get it. After facing reality, I let it go. Oh well. I'm hoping to find someone in the forum with a console Philco to sell and hang on to it until I can orchestrate some way to get. So, the search continues. Thanks for your response. I appreciate it. as always, Garrett Meadows
#4

So what pray tell are you looking for in terms of a Philco console??
If you have some time to kill in a couple of weeks there is a BIG radio meet in Pa. Lots of folks and radios too. A lot of times the consoles go begging unless their something special.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

The radios are up here because Kirk aka Old Restorer has bought 75 percent of the radios available for sale in the United States Icon_wink

Paul

Tubetalk1
#6

Not just radios. Look at the locations of most any vintage electronics--test equipment--or whatever. The bulk of it is east or northeast.

Rob
#7

I found this information on the American Radio History website. It starts on page 24 and list a breakdown of all the radio homes as if Jan 1, 1937. Not sure how this was all obtained, but interesting none the less. Pretty much matches what we knew all along.

http://www.americanradiohistory.com/Arch...937-01.pdf
#8

Very interesting. (I love that website!)
Rob




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM

[-]
Who's Online
There are currently 6558 online users. [Complete List]
» 1 Member(s) | 6557 Guest(s)
Avatar

>