1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 87 cap block
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#1

02-28-2010, 10:57 PM
Are the 2.0 and 1.0UF caps in the cap block e-caps or reg caps....Also the neutralizing caps 7,12,and 17
have the wax out on one and need to be replaced...the schematic show those as a 100 ohm resistor and
a .1 cap as a unit...can i use a .1 cap and parallel a 100 ohm resistor across it for the same results?...OOPS..
the neutralizing caps 7,12,and 17 should be BY-Pass caps!!!!!
Thanks in advance...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

03-01-2010, 09:25 PM
The 1 & 2 mfd caps where originally paper but you can use either for replacement purposes. Go with 600v jobs. Usually neutralizing caps are small variable caps not fixed value paper ones. The bypass caps go from B+ to ground the resistors are in series with the B+. If you connect them in parallel with the bypass you will short the B+ to ground. Not a good thing.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5184 online users. [Complete List]
» 2 Member(s) | 5182 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration