Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phorum How-To #17: Mark Forums as Read
#1

Quite simple, really...

If you visit one of the forums within the Phorum, read the threads you want to read, and then want to mark the rest as "read" all at once - proceed as follows:

Let's assume you are in Philco Home Radios.

Look close to the top of the page, to the right of where it reads Philco Home Radios and under the big Post Thread button.

Look for the Mark this forum read link (see below).

[Image: https://philcoradio.com/images/phorum/Ph...17_001.jpg]

Click or tap it.

You will then see this message:

[Image: https://philcoradio.com/images/phorum/Ph...17_002.jpg]

The message will go away in a few seconds and you will be back on the main page of the forum you were in.



Now let's say you visit the Phorum, but don't want to read any of the threads in any of the forums. You want to mark all of them as "read".

Just scroll all the way down to the bottom of the Phorum home page and look for the Mark All Forums Read link as shown below (the view on phones is similar):

[Image: https://philcoradio.com/images/phorum/Ph...17_003.jpg]

Click or tap it, and then you will see this message:

[Image: https://philcoradio.com/images/phorum/Ph...17_004.jpg]

In just a few seconds, the Phorum home page will reappear.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM
Looking for verification of correct schematic.
I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbe...klondike98 — 12:04 AM
Looking for verification of correct schematic.
Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. ...GarySP — 10:48 PM
HiFi (Chifi) tube amp build - but my own design.
Tim It's be interesting if you put your schematic here. Who knows, you could get some advice from a few folks here. ...morzh — 10:01 PM
Philco 42-390, code 121 speaker
Thanks for that information. It would appear from the output transformer parts list that the transformer that was origi...Stevelog — 07:21 PM

[-]
Who's Online
There are currently 1321 online users. [Complete List]
» 3 Member(s) | 1318 Guest(s)
AvatarAvatarAvatar

>