Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

source for escutcheon screws
#1

Can someone recommend a source for those miniature wood screws that Philco used to attach escutcheons?   I need some for my 41-250 but I've often wonder where to buy them and what size are they?
Thanks,
Keith
#2

Keith, take a look here     https://www.mcmaster.com/#tapping-screws/=1a2gin0

item number 92407A077 might be a good choice.

Steve

M R Radios   C M Tubes
#3

Thanks Steve, I tried searching on ebay but was able to filter on size.
Keith
#4

http://philcoradio.com/phorum/showthread.php?tid=17129

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

The originals were darkened brass, oval head, Phillips screws. Maybe 1/4" long, going from memory here, maybe 3/8". #2 sounds right.

(Edit: Now, having seen the thread Terry referenced just above, #2 x 3/8" does sound right. But the head was oval, not round, made for a Phillips bit.)

I remember finding some in a hardware store many years ago. I should have bought every one they had, I guess...I haven't seen any like that since. The ones I found that time were identical to the original Philco screws.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1835 online users. [Complete List]
» 1 Member(s) | 1834 Guest(s)
Avatar

>