Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New member / Model 60 Restoration On-going
#1

Hi All,

My first post here, and while I have a question, I'll ask it under an already existing thread that it's related to.

Overall, I just wanted to commend you, Ron and all, on the useful information that I've seen so far relating not only to Philcos, but which is also useful for restorations in general.

Ron, your document that pulls together the evolution of the model 60 was especially useful to me since I'm restoring a late model version (the H schematic within your document) for my father, and time is of the essence on this one!

I've done a few radio restorations so I'm not really a newby, but your experience on Philco-specific issues has been VERY helpful to me (aka coil rewinding). I'm an EE, and love working on guitar amps and pedals, and I've done a 41-285 restoration, Trans-oceanic, 46-350 repairs, etc. I have a 630 tombstone that I want to get to next.

The model 60 is coming along, and I have to -- guess what -- do rewinds on the antenna and oscillator coil primaries, as you've talked about elsewhere.

So, thanks again, and if I ever have any wisdom to add here, I'll certainly try!

Scottie
#2

Scottie, welcome. I am sorry I have not participated much here of late. I am in college, and I have a particularly tough semester right now, so I am staying very busy.

--
Ron Ramirez
Ferdinand IN
#3

Ron,

No problem -- I've been busy, too! The model 60 is 98% done, just a few more cosmetic items. The coil winding went just fine, using 34awg wire.

I've thought about furthering the degree, but then I re-think it. Having the time would be a problem!

Good luck with it!

Scottie




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM

[-]
Who's Online
There are currently 3992 online users. [Complete List]
» 1 Member(s) | 3991 Guest(s)
Avatar

>