Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Question about a Philco model 44 code 121
#1

Hi everyone,

    Picked up a nice Philco model 44 cathedral from an estate sale
    over the weekend. While looking it over for the first time I noticed
    the wave band switch worked very well on a up and down gear
    system, but the station selector was free wheeling. My question
    is does the station selector also work on a gear system and if so
    how are the gears set up? I did notice that the selector shaft
    had a small gear on it.
    Also the dial scale is good but dirty. How is the best way to try an
    clean it?
    Thanks for any help and information.

    Tom72
#2

Hi,

Everything you need to know about the model 44 dial drive may be found here:

http://www.philcoradio.com/phorum/showth...?tid=14970

--
Ron Ramirez
Ferdinand IN
#3

Don't use water to clean the dial it will take the ink off of the dial I think there is a post that you should use mineral spirits but don't rub to hard.

Vinzer
#4

Hello Vinzer , Good morning from France Everybody

Indeed , everybody has , on time , encountered the problem of disparition of the inscriptions on a dial , when trying to clean it .

Please which kind of " mineral siprit " do you recommend to use ???

best regards
#5

Ron and Vinzer,

Thanks so much for the information.
Just what I needed.

Tom72
#6

I use whatever is cheapest.
#7

Claude,
I'm not sure what product this would be in France but a typical mineral spirit product we would buy in the local hardware store would be something like this one:
http://www.rockler.com/klean-strip-odorl...4XEALw_wcB

I like to use the low odor type just to keep from stinking up the house.

The Material Safety Data Sheet for this can be found here:
http://go.rockler.com/msds/klean-strip-m...ts-sds.pdf
#8

Claude

It is Naphta Lourd in your case (also White Spirit).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

thanks mike! I thought you might have an international translation for that product... Icon_thumbup
#10
Photo 

Hello Friends

Thanks a lot for détails  !

Indeed , White Spirit is a well known product , used for dilution of most of paints or cleaning art brushes  !

I wish you nice week end  Icon_smile


Attached Files Image(s)
   
#11

Same way it is known in my language, "уайт-спирит", a transliteration of pronunciation of "white spirit" (oo-eye-t spee-reet). Though we stress the last syllable.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>