Posts: 3
Threads: 1
Joined: Oct 2017
City: Alameda, CA
Hi everyone- I was browsing about when I came across what I think is a 46- 1203. It was $40. Swoop. I'm a vintage sewing machine mechanic, and felt like the cord looked decent, sooooo. Yeah. I did it. Plugged it into the strip and turned it on. Everything seems like it works, but i havent checked the needle situation yet. I also dont own any 78s, but that will be a good project, too. (I'll post a picture when i work out the image hosting business)
If someone could point me to the section where I troubleshoot the humming sound, and how to evaluate the needle, I would greatly appreciate it. I also need to fabricate an antenna. I'm telling myself that this is my one and only, but I said that about antique and vintage sewing machines about 30 machines ago....i have low resistance to vintage collections  . Thanks for having me!
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Dolly,
Welcome!
Radios are a bit different from Singers, so plugging an antique radio in a strip not a very good idea.
You got lucky, it did not go up in smoke.
Now that we are past it, you should turn yourself to where it is described how to recap radios (change old capacitors for new ones), and then comes the rest - checking resistors, tubes etc. Oh, and yes, changing cords if they are rigid or cracked.
Philco Electronic Restoration is the chapter here where you could open your own thread and you will get tons of good advice.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi and welcome!
Like your bio reminds me of when I was a kid in the 60's.
You may find this series humorous and educational. https://www.youtube.com/watch?v=rwv36Lr7YoA
The technical info can be found here: http://www.nostalgiaair.org/pagesbymodel...013585.pdf
There are a few skills that are handy when doing service work, being able to use a volt/ohm meter to
check components and measure voltages. Soldering is another, some hand tools, and your good to get started.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 10-27-2017, 12:37 PM by Radioroslyn.)
Posts: 3
Threads: 1
Joined: Oct 2017
City: Alameda, CA
Thanks! Soldering and I are on pretty good terms, from my other mechanicing. Ohm meters and I have yet to meet, but my car can get the Harbor Freight and three different hardwares without me, so I will be looking into that shortly!
Thanks so much for the warm welcome!
Dolly
Posts: 3
Threads: 1
Joined: Oct 2017
City: Alameda, CA
Well, in my defense (hangs head) the store had it plugged in and playing radio, right into the freaking wall, so......Im glad I got lucky! I will Cut it out right this minute. In the sewing world, I have firm rule about never working on anything with a circuit board. Thats where my era of interest ends. (thats where they started using plastic gears and so forth). So, lots to learn!! Thank you for being kind to me! Hopefully, the number of dumb mistakes I make will decrease exponentially now that I have found this board.  Dolly
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!
Lots of great information on this Phorum with threads in the Electronic Restoration section and more specific technical info in the Philco Tech Section. A very nice collection of information for beginners is found on Phil Nelson's website. There's also a better schematic on the Audiophool site. (you need the djvu plug in to view the schematics)
Posts: 12
Threads: 2
Joined: Oct 2017
City: Hillsboro, TX
Welcome! My wife has an old (beautiful condition) Singer I'd love to trade for a Philco!
Kidding, love all old things. Represents a time when craftsmanship mattered more to folks.
Thanks! Cody
Posts: 98
Threads: 2
Joined: Jul 2014
City: Eugene, OR
I have an extra antenna for that unit if you are interested.
Posts: 6
Threads: 1
Joined: Nov 2017
City: Owen Sound, Ontario
Hi Dolly, I just notice you are working on a 46-1203. I am currently restoring a 46-1201. Given that you mentioned that you’re new to this I wanted to make sure you were aware that you can have 120 volts on the chassis depending how you plug it in. One of the first thing I did when restoring my 46-1201 was to install a polarized plug to avoid accidently getting zapped by the chassis during the repair process. .... Jim
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
To avoid getting zapped during the repair process by radios with hot/non-transformer chassis one needs an isolation transformer, and the polarized plug is only good when all is done and the radio is being played. In wet basement. 
I, being an EE, do not touch these without an IT with a 39-1/2' pole.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 6
Threads: 1
Joined: Nov 2017
City: Owen Sound, Ontario
I agree that an isolation transformer is ideal however wiring a polarized plug with neutral on the chassis circuit will ensure the chassis is never hot. I also recommend working with laytex gloves or keeping one hand in your pocket which is what I did 40 years as a young technician.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 40-120C Restoration
|
| Hi David,
Check the cathode bias resistor, it may have changed value. That will affect grid bias, etc. Also, verif...MrFixr55 — 03:26 PM |
|
Philco 91 Restore Code ??
|
| Hi DConnat,
Yes, the 42s are in Pentode Mode, cathode bias. I am using the schematic from the Philco Library, Link ...MrFixr55 — 03:04 PM |
|
Philco 40-120C Restoration
|
| Not my radio just trying to help. DavidDavid — 02:48 PM |
|
Philco 91 Restore Code ??
|
| Thanks Rod. Since the screen grid is not tied to the plate then my tubes are pentode right? I see the candohm ties to th...dconant — 02:29 PM |
|
Philco 91 Restore Code ??
|
| Yes, you can look at the schematic. When the output tube screen grid is connected directly to the plate then it's wired ...RodB — 01:51 PM |
|
Philco 91 Restore Code ??
|
| Can someone tell me if my 42 tubes are connected triode or pentode in fixed or cathode bias? How could I tell by looking...dconant — 10:47 AM |
|
Philco 40-120C Restoration
|
| Hello David,
that is great news about the tubes source being local !
Sounds like you got good start on the radio .
...radiorich — 09:41 AM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM |
|
Who's Online
|
There are currently 2886 online users. [Complete List]
» 1 Member(s) | 2885 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
