Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1934 Packard Car Radio Information
#1
Photo 

Hello,
Can anyone help me locate service literature for a Packard (Philco) P-9 Code 122 car radio?
Here is a photo of the decal inside the set.

Thanks,

Paul


Attached Files Image(s)
   
#2

OK, apparently a model listed as a Philco Model 9 in NA. is very similar to the P-9. Tube compliment is the same, and I will investigate if they are one-in-the-same radio. 

Can anyone confirm this?
#3

Welcome to the Phorum!
Icon_wave

Have not worked on any car radios so can't help you but others may have info.
#4

The power supply looks like it was off board connected to a female ended cable, which could have been connected to either sets of batteries, or a vibrator supply, the tube filaments may or may not have been in series. The earliest car radios were very much like a farm or portable radio installed in a car with a set of "A","B", and "C" batteries to power it, and almost all were aftermarket installations, Packard may have been one of the earlier marques to offer a radio as a factory option since they were higher end cars to start with. I could look in my Philco factory manual but I'm not sure if it has any car radio schematics in it, it was given to me by an uncle who tended to eschewcar radios and TV schematics so they may have been edited out of the binder.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 1582 online users. [Complete List]
» 1 Member(s) | 1581 Guest(s)
Avatar

>