Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ
Has anyone replaced a tube socket on a 48-2800? My rectifier socket is beyond soldering due to damage to the pin for the AC/filament connection. I overheated the terminal to destruction. It started out with too much solder causing shorting to the adjacent pins. After much sucking removal the terminal itself broke off. Is it worth it?
Welder
Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN
I would think so shouldn't be that hard.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
48-2800???
Are you sure you have the right model number?
--
Ron Ramirez
Ferdinand IN
Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ
Hi Ron:
It should be 48-200. Sorry about that. Thanks for pointing it out.
Welder
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
I know that the first time that you change a socket, transformer, tuning cap and such it can seem overwhelming - it isn't. Take some pictures before you start and take your time.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ
Phlogiston:
Thanks for the encouragement. I'll take pictures and begin the procedure and look at it as another step in gaining experience for future restoration.
Welder
Posts: 7,253
Threads: 267
Joined: Dec 2009
City: Roslyn Pa
Check ur pm box.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 15,473
Threads: 541
Joined: Oct 2011
City: Jackson, NJ
I think you should
1) disconnect the wires and label them;
2) make a sketch of what wire went where;
3) if any components are soldered directly to the socket, I'd leave them there.
4) drill out the rivets such that you do not increase the existing hole diameter.
5) extract the socket.
6) remove the components from it and transfer to the new socket.
7) rivet or screw the socket in place. If the socket is metal, riveting is fine; if fiber - be careful, possibly using softer aluminum rivets or putting a metal washer over the socket, watching so it doesn't short the pins.
8) solder the wires back.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ
Morzh:
Thanks for the check list. I'll definitely use it when the socket comes in.
Welder
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
WELL,,,Pipefitter telling a welder,,,,,get'er done,,,more heat,,,,,You will be fine,,,CHEERS
Posts: 4,648
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
There are two more things that you need to watch for when you replace a tube socket, one is the distance between the two rivet holes in the chassis, the other is the diameter of the socket hole in the chassis. If the replacement socket is a used one salvaged from another Philco chassis there should not be a problem with either dimension. There is one more thing that you need to be aware of in case you buy a new socket from China or from one of the countries of the former USSR, and that is the mounting system used. There is a design of octal socket where the socket can be mounted either on top or bellow the chassis depending on how you use the metal bracket that comes with it, an old radio chassis may not have enough space underneath for the bracket, and there may not be enough height inside the cabinet to mount it on top. These sockets are available in both porcelain and in Bakelite. Another think to watch is the fact that these countries frequently give measurements in millimeters, which is fine, but make sure that the conversion is right before you order.
Regards
Arran
Posts: 15,473
Threads: 541
Joined: Oct 2011
City: Jackson, NJ
I would mount on top: when you put a tube in the socket, if it is only supported by rivets, its ears will bend.
Whereas if on top, when you press on it, it is supported by its whole rim against the chassis. And when pulling the tube, it is not really pulling with loctals but bending at an angle, so no truly pulling effort exists.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ
Morzh:
Good idea mounting so the chassis bears the stress of tuging on the tube .
Thanks,
Welder
Posts: 4,648
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
The mounting ears are not likely to bend, the gauge of sheet metal they used in the mounting bracket is fairly thick and the length is maybe 1/4'' at most. The ears on wafer sockets are just two layers of sheet phenolic plastic and they seem to hold up, if anything the terminals pull out of the socket before the rivets will pull through. Just copy the way Philco mounted the socket and everything should work out.
Regards
Arran
(This post was last modified: 12-16-2017, 01:00 AM by Arran.)
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Philco Model 71B
|
Is the arch area on the front of a Model 20 real or photo?MrFixr55 — 07:31 PM |
Eico 584 schematic
|
Anyone have a schematic for this tester?daveone23 — 05:48 PM |
Philco Model 71B
|
Good one!!! No if I go for it, I’ll fix it right lolslford310 — 04:38 PM |
Philco Model 71B
|
Stucco on the arch?RodB — 04:31 PM |
Philco Model 76 Highboy
|
Back in Feb I scored a nice model 95 Highboy, see earlier post. Saved from a guy that likes chopping them up into Liquo...slford310 — 09:49 AM |
Philco Model 71B
|
Adding a pic from the other side and the inside. It will be a bit of work and a challenge but that's what makes it fun....slford310 — 09:32 AM |
Philco 89B code 123 newbie
|
Hi Kurt
Welcome to the Philco Phorum. Lots of phriendly pholks (see a pattern here?) who are happy to help. Keep posti...MrFixr55 — 08:36 AM |
Philco 89B code 123 newbie
|
Hello Kurt,
Welcome aboard and you have a nice set to start on !
Yes, the bakelite blocks and I too find them fairly...radiorich — 07:12 AM |
Philco 89B code 123 newbie
|
Getting started on my first Philco here, done some research and hopefully I now know enough to be dangerous. :)
Overal...Kurt P — 01:44 AM |
Delco car radio Peko vibrator converstion issues
|
Richard,
I reviewed the Panasonic specification sheets for this type capacitor and though dV/dt is discussed, there a...Chas — 11:48 AM |
Who's Online
|
There are currently 2321 online users. [Complete List] » 1 Member(s) | 2320 Guest(s)
|
|
|
|