38-690 Refinish June Update
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
I am looking at refinishing my 38-690 cabinet. Appears to be done over with polyurethane with a few runs and rough finish. Looks like it was slathered on too thick.
I was curious if there is any photo finish on this radio, especially the front. From what I can tell it's veneer but sometimes it's easy to be wrong. I tried to strip a slightly hidden spot with lacquer thinner, and it appears to be veneer as there are grain pores visible.
I don't want to strip it and find out that I ruined the cabinet.
Also, what wood type is this cabinet? Seems light for walnut, but it has open grain so it's possible.
https://www.flickr.com/photos/152428891@...ed-public/
(This post was last modified: 06-03-2018, 05:52 PM by tbone.)
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
As far as I'm concerned there is no photofinish on this radio: strictly veneers and toning.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
No photofinish on the 38-690. Ron generated a handy list of models that have photofinish and its in the Tech Section.
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
Ok that makes sense. I think it was around 1940 when they used photo finish quite a bit.
Thank you.
This is going to be quite a job, but I should be able to use a citrus stripper to do this in sections. The hardest part will be the roll top which is on canvas. Not sure about that yet.
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
Thanks for the link Bob!
(This post was last modified: 12-28-2017, 07:17 PM by tbone.)
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
A radio of this class and photofinish kinda make little sense together.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 7,273
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Midway thru 1936 ('37 model year) and there after was BIG on the Philcocoat (photo) finish.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
(12-28-2017, 07:14 PM)tbone Wrote: Ok that makes sense. I think it was around 1940 when they used photo finish quite a bit.
Thank you.
This is going to be quite a job, but I should be able to use a citrus stripper to do this in sections. The hardest part will be the roll top which is on canvas. Not sure about that yet.
Philco had a lot of photo phinish by 1937.
I doubt that "citrus stripper" is going to work on poly, it hardly works on lacquer.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
Chemical paint strippers seem to work on poly effectively, but are stinky and you have to wear gloves as they really harsh on skin.
Water based paint stripper also work but much slower.
The photo finish, as I understand it, was mostly used on tabletops in 1937? The consoles I saw, especially the expensive ones, like 37-116, don't seem to have it?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Mike
Some of Philco's low end consoles, including the 37-33, 37-34, 37-60 and 37-61 (among others), used photofinish on the front panels. You are correct, the high end consoles such as 37-690, 37-116, 37-675 and others, used real wood veneer and no photofinish.
I made some additions to the list Bob linked to in post #3 above. Philco used photofinish on some 1941, 1942 and 1946 models also, as well as some models in later years (which are not in the list).
--
Ron Ramirez
Ferdinand IN
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
Thanks to Ron and everyone for the information which will be helpful going forward.
I will be stripping the cabinet myself, and most likely will be using a citrus gel stripper I have had good results with before.
Does anyone know what type of wood the main cabinet is? Reason I ask is that I would like to buy something close to experiment on so I can get the coloring correct. Kind of a practice piece.
Thanks again.
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
If you just have to use stain - and you don't have to, I would stick to using it just on the hardwood trim (poplar or ?) at the base and the edge of the top, not on the veneers.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 275
Threads: 18
Joined: Nov 2016
City: Cromwell
State, Province, Country: CT
I was actually thinking about toners for the base (feet) which is not the best wood, grille bars, and the rim around the top. I agree that the dark veneer and pretty much the whole front should be left as is.
I will know more once I get to the Grain filler step. I believe that only the top, sides, and front panel around the dial will need this step. The dark veneers around the front are not that open of a grain.
Tony
“People may not remember how fast you did a job, but they will remember how well you did it”
Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ
The veneers on that cabinet look beautiful. That is going to look awesome when you're phinished!
Users browsing this thread: 2 Guest(s)
|
Recent Posts
|
Correct model 84 Ac plug an cord type
|
Hello Arran
Yes, I also like the lampshade style plug !
Sincerely Richardradiorich — 08:46 AM |
Restoring Philco 38-14
|
Hello morzh,
Nice explanation on the x and y capacitors and glad you are narrowing down the issue with this set !
Si...radiorich — 08:43 AM |
Correct model 84 Ac plug an cord type
|
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM |
Correct model 84 Ac plug an cord type
|
Hi Bruce,
I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM |
Restoring Philco 38-14
|
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder.
I put a scope on the o...morzh — 08:15 PM |
Correct model 84 Ac plug an cord type
|
Hello Bruce,
I mostly use brown far as my cloth powercords go !
Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM |
Correct model 84 Ac plug an cord type
|
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM |
Restoring Philco 38-14
|
Rod
Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios w...morzh — 10:11 AM |
Restoring Philco 38-14
|
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM |
Restoring Philco 38-14
|
hello morzh ,
That sounds like a plan !
Sincerely Richardradiorich — 07:45 AM |
Who's Online
|
There are currently 3035 online users. [Complete List] » 1 Member(s) | 3034 Guest(s)
|
|
|
|