Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Hi everyone. Just finished recaping 47 1230, and am works great. My problem is no fm . When switched to fm 1 station is clear and when tuning for other station this one station stays on no matter where I move the tuner. Any ideas ? Thank you.
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Welcome to the Phorum!
If I recall correctly that set has both pushbutton tuning and manual tuning. Pushbutton tuning is a separate tuning circuit that bypasses the variable cap tuner. To tune manually there is a button to switch to the manual tuning circuit.
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
Klondike is right , the pushbutton tuner is separate from the manual tuner and needs to be tuned separately by coils on top of it. If you are using the mannual tuning, does it move the pointer?
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Thank you for the replys ! The tuning cap is moving, but fm is completely silent. I tested all tubes except the 7F8, which my tester had no info on. I will have to make some voltage measurements around the 7F8. I cleaned the bandswitch with deoxit,but that changed nothing. Thanks again !
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Well I really need some help. I replaced 7f8 tube with a NOS, still no fm. I then proceeded to make the feedthrough mod on c419, now I have no AM or Fm or SW. Could this mod mess up the oscillator ? I'd appreciate any help or comments.
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
There is a troubleshooting guide in the service bulletin. Might be the best way to locate the problem.
See: http://www.audiophool.com/Philco.html for the bulletin.
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Thank you Bob for replying. I have that and guess I'll have to start all over. Regards, Bill
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
I've not worked on that model and don't have the troubleshooting skills to suggest something, maybe others will have some thoughts.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
(02-07-2018, 06:10 PM)willydcamaro Wrote: I then proceeded to make the feedthrough mod on c419, now I have no AM or Fm or SW. Could this mod mess up the oscillator ?
Well, it could...if you did not hook things up correctly when you replaced C419. Also, you could upset the screen grid voltage of the two IF amplifier tubes when the radio is set to FM. I think some voltage checks and circuit tracing is in order.
--
Ron Ramirez
Ferdinand IN
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Hi Ron. Thank you for replying ! I will start taking voltage checks tomorrow. Thank you Guru !!
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Good Morning. I noticed on the instructions that a metalized film cap should be used for c419. I used a polypropylene.....would this make a difference ? Thank you,Bill
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Hi everyone, Weii I undid the C419 mod, soldered in the old C419 and I now have AM and Shortwave back. Now back to no FM.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
You must have connected the new C419 incorrectly...or else your new capacitor was bad (it happens, but fortunately very rarely).
--
Ron Ramirez
Ferdinand IN
Posts: 69
Threads: 4
Joined: Apr 2016
City: washington nj
Well...still at it. Now I have 303 volts from 5y3gt to R100 15 k resistor but nothing after the resistor. Any help would be appreciated, Thank you, Bill
Posts: 7,266
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi Bill
Well seems like you have a few possibilities. 15k resistor is open/ bad connection or something that it is feeding the 190v is shorted. One way to troubleshoot this short issue would be disconnect parts that go from the 190v circuit to chassis ground like C-102A while using an ohm meter across the 190v line. Set unplugged of course. What you are looking for is a resistance of abt 5000 to 100000 ohms or so. What you have now is something very low probably in the 10's or 100's of ohms. Ecaps will look like a short at first (for a few seconds) as as they are being charged by the voltage from the ohm meter. But after words should show a high resistance if good. Connect the black lead to the chassis from the meter. The other way around it may try to charge the cap backwards showing it to be shorted when it isn't
Happy hunting!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 02-11-2018, 03:24 PM by Radioroslyn.)
Users browsing this thread: 2 Guest(s)
|
Recent Posts
|
42-345, question for an owner
|
+1 for number 4 with an added theorem: The more connections in a circuit the higher the possibility of failure.RodB — 12:17 PM |
Help with Readrite 410 tube tester
|
IMHO, Between the transformer common (where you have one lead) and any point on the rotary switch, you should be reading...MrFixr55 — 11:53 AM |
Help with Readrite 410 tube tester
|
This is such a simple looking schematic yet its throwing me off and driving my Fluke DMM crazy. I cant get real voltage ...daveone23 — 11:23 AM |
42-345, question for an owner
|
Rod
:lol:
1. The schematic always work according to the wiring.
2. If the schematic does not work according to the wir...morzh — 10:36 AM |
42-345, question for an owner
|
Wow Mike, that's profound! That should be the Phorum motto.RodB — 09:49 AM |
Philco 269 - 444 FIVE VALVE VERSION?
|
Hi Chas,
I hear you. If you happen to be passing NYC vs Philly, I can give it a good home also.
@ RadioRoslyn, T...MrFixr55 — 09:25 AM |
Bakelite crack repair - what is best epoxy?
|
I'm with Arran, but I use even stronger epoxy with a 72 hour cure. It is sold to knife makers for bonding wooden handles...DaleHCook — 08:47 AM |
42-345, question for an owner
|
It cannot be wired correctly and work incorrectly.
It is as simple as this: if you want to have you treble up and bas...morzh — 08:33 AM |
42-345, question for an owner
|
Welcome to the Phorum, Noel! I don't have that radio, but I'm sure others will jump in with help. Take care and BE HEA...GarySP — 07:52 AM |
42-345, question for an owner
|
Hello,
I am working on a Philco 42-345. It appears that there have been many hands inside this radio before me....UpNorth — 07:42 AM |
Who's Online
|
There are currently no members online. |
|
|