1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 680 Shadograph.
vaguy22
Junior Member
**
Posts: 41
Threads: 12
Joined: Nov 2012
City: Suffolk, VA
#1

02-02-2018, 10:50 PM
Has anyone fixed a Model 680  shadowgraph. I tried the usual hints from the " repair bench" with no results. the vane is free and coil shows 500 ohms resistance. #85 tube is good with 70 volts plate voltage. Thanks in advance   Norman
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,887
Threads: 214
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

02-02-2018, 10:56 PM
Any chance that the bar magnet has become demagnetized?

500 ohms sounds low to me for the coil resistance - typically they're >1K.
Find
morzh
Odobenus rosmarus
******
Posts: 16,482
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#3

02-02-2018, 11:14 PM
Even if 500 ohm, still should react.
I second the magnet thought.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

02-03-2018, 10:08 AM
Just for grins take a 9v battery - to the chassis and + to the grid cap of the 85. Should cause the vane to deflect.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
vaguy22
Junior Member
**
Posts: 41
Threads: 12
Joined: Nov 2012
City: Suffolk, VA
#5

02-06-2018, 10:26 PM
Thank you folks for the hints. Norman
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM

[-]
Who's Online
There are currently 370 online users. [Complete List]
» 2 Member(s) | 368 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration