1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Knobs for Philco 52-1731
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#1

03-05-2018, 01:50 PM
Hello: I'm restoring a Philco 52-1731 cabinet and am missing 2 of the 4 tuning knobs. Any suggestions on where to obtain 2 of these could be much appreciated. Images of the knobs are attached. Thanks!


Attached Files Image(s)
   
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

03-05-2018, 01:56 PM
Welcome to the Phorum!

For the knobs check with Gary at http://oldradioparts.com (looks like he's closed until 3/11).
Find
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#3

03-05-2018, 02:19 PM
Thank you, Nathan! I will reach out to Gary next week...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

03-05-2018, 11:54 PM
Philco Knobs & Pushbuttons (original)

David Frush (original and NOS knobs, including many for Philco sets)

Julie McCall - Original knobs for Philco and other radios.

Kelton Trammell - Original knobs for Philco and other radios.

Mark Oppat's Old Radio Parts

Mike Koste - Gobs of Knobs

Here at the Philco Phorum we have a Resource section has listed parts and services available for Philco sets.
Personally have had dealings w/ Julie and Mike both are top notch!

Welcome to the Phorum.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#5

03-06-2018, 01:13 PM
Much appreciated, Terry
Find
Arran
Phorum Expert
*****
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#6

03-09-2018, 02:43 AM
Or you could keep your eyes open for a smashed early 50s Philco plastic radio or junker radio-phono combo, many of those use the same style of knobs.
Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5441 online users. [Complete List]
» 1 Member(s) | 5440 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration