1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-9 How to remove Bezel from Cabinet?
philconerd
Member
***
Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN
#1

04-11-2018, 10:23 AM
Hello Forum.  I need help with this Bezel removal.  i am just starting on this radio project and I want to get the cabinet ready for refinishing.  Then on to the chassis later next month.

Anyone know if it is glued on the cabinet or fastened some way?  

This is a family heirloom radio from a friend  and it is in very good original condition.

Thanks.
G.

   
Find
John Bartley
Senior Member
****
Posts: 358
Threads: 4
Joined: Aug 2015
City: Monteith, Ontario CA
#2

04-11-2018, 11:19 AM
I think the outer ring rotates CCW a couple of degrees and then pops off? Behind it is a locking ring that screws to the cabinet?
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

04-11-2018, 12:11 PM
+1 gently pressing it inward.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
philconerd
Member
***
Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN
#4

04-11-2018, 01:41 PM
John & Terry-

Thanks for the tips, that did it.  Just the CCW  twist and the outer plate came off.
Then removed the 4 screws and it's done.

Thanks again.
G.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#5

04-11-2018, 08:30 PM
ALWAYS be careful as the glass is not secured by anything...
It falls right out... I broke one last month Icon_sad
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
philconerd
Member
***
Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN
#6

04-12-2018, 10:25 PM
Yes,

i have the glass safely stored away until the time comes to put everything back in the cabinet.



G.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM

[-]
Who's Online
There are currently 2012 online users. [Complete List]
» 1 Member(s) | 2011 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration