Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 14 LZX resfinish
#16

Hi folks - chimeing in as I heard my name Icon_smile

The picture shows a hole pattern exactly the same as I tried to reproduce. This I did from a picture on the net, scaling to get hole size and spacing.

I estimated holes are 1-3/8, spaced at 2". Top row is 10 holes, next down is 8. The whole pattern, top to bottom goes:

10, 8, 10, 8, 10, then again 10, 8, 10, 8 10.

Hope that is helpful,

Ed

I don't hold with furniture that talks.
#17

(04-14-2018, 10:00 AM)gregb Wrote:  I am recovering from knee replacement surgery...

Ouch, sorry to hear that. Best wishes for a speedy recovery! Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#18

Thanks Ron, its coming along just fine and I am just starting to walk unassisted. Its been a long slow recovery and not a whole lot of fun but everyone I have talked to that has had this done say its worth all the trouble, fingers crossed!

Gregb
#19

Greg

Feel better, hopefully it's worth all the suffering through it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#20

Thanks Mike, I am looking forward to the end game.

Gregb
#21

Busy as a Beetle over the weekend, had to go to regular job Saturday and paint a Mercedes Benz then I went to radio shop and worked on the Philco, sorry but no book match veneer this time on the radio top, didn't want to spend the $85 on the wood just for the top never get it back. Although the walnut veneer I put on has some very nice grain pattern running thru it it will be very nice once finished. The toning isn't factory but really looks nice, the finish isn't done yet. I have to sand the sealer which your seeing in these photos, then apply the final coats of clear lacquer and the gloss level will be higher. The speaker cabinet has new walnut veneer on the top and matches the radio cabinet, the factory had walnut running fron left to right on the speaker cabinet. Still waiting to hear from radio daze on the dial, next week I will finish the radio and speaker, new cloth for speaker and a new back cover will be made but I'm thinking about using  1/4 wood that will be stained and cleared and perhaps not drilling the holes. I'm thinking the radio may have more Bass if I don't drill the holes in the back cover, what do you thing Ron?


Attached Files Image(s)
                   
#22

More pictures


Attached Files Image(s)
                   
#23

Hello Ron, radio daze has this dial its for a miodel 18lzx I'm wondering it sure looks like what I need , will this work is what I want to know. Thers a few little deferences in the short wave band numbers but not much and the size of dial not sure if same size as 91? or the 14lzx chassis.


Attached Files Image(s)
           
#24

> I'm thinking the radio may have more Bass if I don't drill the holes in the back cover, what do you thing Ron?

It will have plenty of bass with the proper back. It's up to you if you want to install a plain back with no holes, though.

> radio daze has this dial its for a miodel 18lzx I'm wondering it sure looks like what I need , will this work is what I want to know.

Will it work? Yes. Will it be authentic? No, simply because the 18RX has a different coverage on its band 2 than does the 14LZX (1.5 to 4.2 mc in the 18 versus 1.4 to 3.3 mc in the 14LZX).

--
Ron Ramirez
Ferdinand IN
#25

Hey Fred, I would just give the guys at Radio Daze a call, they will make anything you want and for the same price you would pay for the one above. I have had them done with no problems.

Gregb
#26

Finished up the cabinets except the back cover for speaker, the walnut veneer I replaced on both tops on speaker and radio came from same sheet and match perfectly. No book match on radio, the veneer was very expensive so I decided not to go with it . The toning was done to give the pieces a little bit more character and style , more than what the factory had done. This set would be a great addition to any radio collection. I will post pictures of the radio when I get done with the chassis and have it installed.


Attached Files Image(s)
                   
#27

Few more pictures, the speaker cloth from Radio Daze and is the cloth for the 90 cathedral, so I kept the pattern in the family.


Attached Files Image(s)
                   
#28

That looks good Fred.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#29

ALL ,,I ,,,CAN say is ------SHOW ROOM Material
#30

Fred, your work is amazing!

Steve

M R Radios   C M Tubes




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-2 Automatic Tuning
Hi Richard, I enjoy it to some extent. I do that type of work out in barn (modern) during the summer on nice days when I...dconant — 03:13 PM
Philco 38-2 Automatic Tuning
hello dconant , my set is the tabletop one and it also needs refinished someone put plant or something on top and the f...radiorich — 02:56 PM
Philco 38-2 Automatic Tuning
Well, you could take a look at most features of those radios, and other than some very few of them, they all are selling...morzh — 02:20 PM
SABA 400 Automatic Stereo 11
I actually got to hear the SABA play today when I took my Westinghouse AM-FM up to be worked on and also now know a pric...Jayce — 02:08 PM
Philco 38-2 Automatic Tuning
Seems more like a selling point to me. I too have have a Philco with the Cone-Centric tuning. Hopefully I will get the ...dconant — 12:17 PM
Philco 38-2 Automatic Tuning
I found out, I never use it in my 37-116 and 38-690. I made sure it works, but this was it: I always hand tune.morzh — 10:55 AM
Philco 38-2 Automatic Tuning
Does it wash your windows? Then it would be useful and worth fixing. Music and window washing.RodB — 10:00 AM
Philco 38-2 Automatic Tuning
You press the lever (crank) and you rotate the dial into the desired position. Also, while pressed, the contact that it...morzh — 09:50 AM
Philco 91 Speaker Replacement
I do not have much experience with speakers, but acetone sounds right. It does not affect paper but does dissolve about ...morzh — 09:48 AM
Philco 38-2 Automatic Tuning
Hello Dconant, In my collection I have a model 38-7T which Philco called their famous "Cone-Centric" dial me...radiorich — 08:14 AM

[-]
Who's Online
There are currently 1710 online users. [Complete List]
» 1 Member(s) | 1709 Guest(s)
Avatar

>