Started the restore on my Philco 40-180.
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
Got it up on the bench, there's a lot more dings in it that I thought. But still workable. The whole top center , and face plate some one had tried to take out by removing some screws, but never replaced them. It actually came off pretty easy. Now I noticed what looks like a plastic plate that went from one side to the other with 2 screws on each side. The middle is missing just the corners are left. Does anyone know what that was? Here's a picture:
[attachment=16558]
Also the veneer on both sides of the speaker are in pretty bad shape I may have to replace quite a bit of it.
[attachment=16559]
[attachment=16560]
What do you think, should I try to just replace the bad parts, or replace the whole strip?
Michael
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
I used a stripper to remove the lacquer, that worked pretty good, just a little sanding. Had the face plate, and both sides of the face plate plus the speaker bars, removed that made it a lot easier. I'm down to the two veneer strips on both sides of the speaker. Still haven't decided if I will try to repair the strips, or replace them.
Michael
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
(This post was last modified: 06-15-2018, 11:45 PM by nortonz.)
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
Can someone tell me if the veneer strips on both sides of the speaker is zebrawood?
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
I have to replace some veneer on both sides of the speaker, I think it's zebrawood, but don't know for sure, can someone confirm.
[attachment=16588]
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
I would go to the Albert Constantine's website. and have a look at their veneer gallery to compare it with what they have. I'm guessing it's zebrano, or zebrawood, but it may be may be something like orientalwood. I would also have a look at what they have for eucalyptus veneer which can look similar sometimes. Unless someone has an original ad describing the cabinet, and what veneers were used, we can only make an educated guess.
Regards
Arran
(This post was last modified: 06-19-2018, 03:56 AM by Arran.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Two threads on same subject merged into one.
Ref. Phorum Rules:
Quote:II. Multiple threads on the same subject not allowed.
When you start a thread, please keep the discussion within the same thread.
Example: "Philco 90 broken"
After you've started that thread, please do not start another thread on "Philco 90 bad resistor" if it is the same Philco 90 being discussed in the original thread. Give others a chance to respond to your questions rather than asking them again in a new thread - please be patient.
http://www.philcoradio.com/phorum/showth...p?tid=4586
--
Ron Ramirez
Ferdinand IN
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 14
Threads: 3
Joined: May 2018
City: Alexandria
State, Province, Country: Louisiana
I HAD to replace both strips on my 40-180. Haven’t completed the job yet, hope to finish tomorrow and will post a picture of the completed cabinet. I used rosewood veneer to replace what few pieces of the original I had. Put some Clear Sanding Seal on the veneer after gluing it to the substrate. Looks pretty good to me. Will post picture soon.
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Russ;
It's hard to tell sometimes, it may just be a case of the cabinet being sun bleached, the grain pattern is very close though, maybe if he chisels some off and takes a look at the underside? However to me it looks a bit like Eucalyptus. I also don't think it's a type of rosewood, that stuff has wider dark portions to the grain, and it's more on the red side.
Regards
Arran
(This post was last modified: 06-19-2018, 04:01 AM by Arran.)
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
The cabinet is all ready to seal, just have to do something with that veneer, been looking at different types, trying to figure out what to use. The other problem I'd the original the grain goes on an angle, so to replace the whole strip would take a fairly large strip. I think I have decided to replace both strips, they are both in pretty bad shape.
Michael
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Yes, replace both since they are supposed to be book matched - so you will need to consecutive pieces, like the one in my picture, to cut them from.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
(06-18-2018, 09:51 AM)Phlogiston Wrote: I don't think so.
Zebrawood on AK
More:
https://www.russoldradios.com/blog/atwat...-condition
Where did you get the zebrawood veneer that size?
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
E-Pay.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID
Ok what is "e-pay"?
Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
eBay.
http://www.ebay.com/
Also known as "E-Pay", "Pay-Bay", "the auction site", etc., etc. ...
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 38-7 Oscillation
|
| I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM |
|
Philco 38-7 Speaker
|
| I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM |
|
Philco 60 Squealing
|
| I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM |
|
Philco 42-390, code 121 speaker
|
| These speakers pop up on eBay regularly, even if at bloated prices.
Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM |
|
Philco 38-7 Speaker
|
| The put-put is not like the speaker problem.morzh — 08:29 PM |
|
Mission Bell Model 19A Car Radio
|
| Hello everyone,
As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM |
|
Philco 60 Squealing
|
|
Wondering if I did it backwards.
If a coil was wound backwards, the oscillator would not work at all.
Old school...Chas — 07:23 PM |
|
Philco 38-7 Speaker
|
| 4-ohm speaker. Black, Green leads.tludka — 07:00 PM |
|
Philco 42-390, code 121 speaker
|
| #87 on the schematic.
This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM |
|
Philco 60 Squealing
|
| I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM |
|
Who's Online
|
There are currently 4053 online users. [Complete List]
» 2 Member(s) | 4051 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
