Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 90 Tube Shield
#1

I’m considering buying a Model 90 cathedral that is missing the large 3-tube tube shield. Philco made three versions of this model with different output tubes (early w/ two 45s; mid w/ one 47; and late w/ two 47s). “My” radio is the mid version. Does anyone know if the large tube shields for these three models are interchangeable? The early and mid versions appear to have the same tubes and tube layout for the tubes in the large tube shield (24, 27 and 24). The late version appears to have different tubes and a different tube layout. Therefore, perhaps the early and mid versions are interchangeable.

Additionally, the radio has a vertical bracket on the opposite side between the rectifier (80) and output tube (47). You can see the bracket in this video (5 minutes into video): http://www.youtube.com/watch?v=ptQ2d0VsZmc Does anyone know the purpose of this bracket? Another tube shield?

Thanks!
#2

Hi Allen

Sorry for not replying sooner.

The large tube shields for the early (2-45) and mid (1-47) are interchangeable; the shield for the late version (2-47) is different and is not interchangeable with the early and mid versions - but the third version shield is interchangeable with Model 91.

Yes, the flat metal in the mid version is another tube shield; it serves mainly to protect the two 27 tubes in the audio circuit from interfering with one another, I believe. In early versions of the "mid" chassis, there was a single round shield over the 27 tube that is next to the 47 output tube. This was later changed to the flat shield which is missing in your set.

--
Ron Ramirez
Ferdinand IN
#3

Hello Ron:

Thanks for your reply. Using your information, I found photos on ebay of several Model 90’s with both tube shields. Now I know what I’m looking for should I decide to purchase the radio. I'll try to attach the photos for reference.

I appreciate your time and assistance.

Allen



Note from site admin: Sorry, but the photos which were attached to this post are no longer available.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2118 online users. [Complete List]
» 2 Member(s) | 2116 Guest(s)
AvatarAvatar

>