Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

*Solved Minerva Tropic Master model w117 "early"-crackle pop & no vol ****SOLVED

I believe springy material on brake lines is to reduce vibration, lessens chance of a rub through. Older vehicles like my '69 Cobra Jet didn't use them, but my '72 Comet does have wrap on lines.

Tom

wiper to ground reads about 7 ohms this time, sometimes its 10, others is 2 and other times its like 20 but still low enough.

so... the ref gnd signal is stable enough to not be the fault for this.

it could be several things.

i tried calibrating down in resistivity of the 47kohm R after the wiper,, still have sound with vol at Min.

i think i will just live with it.

this bugger gets really HOT on the outside,,

headed out to put it back inside its carry case after i add my antenna relay back on.
i am considering a 120 v small fan to mount inside it....

new cooling fan in,,, now that really took care of the heat.


air intake is in the "back door"
air hits ceiling and goes left and right out the side louvers.


Attached Files Image(s)
       

i really want to add a couple things to this set

i want an S meter

i want a BFO even if its a gimick type.
i am getting a lot of side band in addtion to shortwave

i am going to start with the gimmick BFO type for side band if anyone has suggestions.

i know i will need another tuning cap which i have several.

from there i will need a knob on the tuning cap which i have.

i can string up and make a 0-100 scale which will be visible in the lower part of the main tuning window just below the words printed "tropic master".

how do i wire in such a thing?
do i attempt to copy cat the gimmick from my hallicrafters S38-d which actually works really great!.

any ideas or anyone experienced in doing this?

Hello friends, I loved seeing all the work in this rarity of 1944, I have a radio of this model here and I need to restore it, it is not as beautiful as this one on the topic, what was written in most components has worn out over time, I need to replace components mainly capacitors, I don't have his technical documentation, if any of your friends know of a site that I can download, please let me know, thank you very much !.

W-117 early version:

http://www.nostalgiaair.org/pagesbymodel...010877.pdf

W-117 late version:

http://www.nostalgiaair.org/pagesbymodel...010878.pdf

Better copies can be found here:

https://worldradiohistory.com/Archive-Ri...45-MNO.pdf

Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM

[-]
Who's Online
There are currently 721 online users. [Complete List]
» 1 Member(s) | 720 Guest(s)
Avatar

>