Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1936 Philco Radio Bar featured in Humphrey Bogart's "One Fatal Hour"
#1

I spotted a beauty of a radio bar in the Humphrey Bogart film "One Fatal Hour" on TMC. Interesting film, too. All about ethical issues in that new-fangled radio business.

Charlie in San Antonio
#2

You missed the late 1936 model 60B at the news stand and the 17X. The 60B has a close up shot but a few seconds later it morphs into a small cathedral (not Philco I think).
https://www.dailymotion.com/video/x21hhcx

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I just saw that today, in fact the majority of the movies on TCM today seemed to be on a radio broadcast theme. I did see the RadioBar, but I also saw a 1932-33 vintage Philco X console with an inclined sound board, it may have been a model 17X. The film was a little too melodramatic in my opinion, and I highly doubt whether even a real slimeball of a radio station, and it's employees, would do such things back then as their lawyer would be blowing his stack about the libel suits, as well as the FCC/FRC taking their license away.
Regards
Arran
#4

Here it is


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#5

Did anyone record that movie? I would like to have a copy.

Tim KA3JRT
#6

Click on the link on the second post.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

Wow! A little less than stellar performances.  Did like the Radio Bar, though.  I want one, but only willing to pay double original retail.
#8

Quote rfeenstra: "Wow! A little less than stellar performances.  Did like the Radio Bar, though.  I want one, but only willing to pay double original retail."

 I concur, though I don't think that Bogey's part was a less then stellar performance, but like the early 80s rendition of Scarface, most of the movie was a pile of fromage aside from Al Pachino's performance carrying the film. I also agree with you regarding the Radiobar, but I would like an inclined sounding board "X" model Philco more, possibly a model 115X, though a 16X would do nicely as well. I've only seen one on the market nearish to me, it was a model 91X (or was it 391X?) the set was a basket case, trashed speakers, no knobs or escutcheon, and too far away, most Canadian Philco cabinets seem to have been low or highboys, even as late as 1936.
Regards
Arran
#9

And then there is this 1937 Philco Bar radio on eeevilPay for a modest $29,999.00 or best offer which translates to $39,362.00 worthless Canuckastan Beaver Pelts. For that price it better be fully stocked with boooooze to drink oneself unconscious after shoveling out that much coin.
#10

And my pictures didn't appear to upload. The joy of smart phones.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4076 online users. [Complete List]
» 2 Member(s) | 4074 Guest(s)
AvatarAvatar

>