Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE 200
#1

Forgive the lack of photos hopefully to follow. I bot a GE 200 off the bay. Looked good. Arrived and the box was rattling o I was a bit nervous. It arrived OK, dial glass was loose and I cleaned it up a bit. Tubes look like 4 non original so maybe they are all good. The slant chassis is cool and with 6 tubes probably play OK. I have been warned about how sensitive the dial glass numbering is and despite my most gentle attempts at cleanup the General Electric words got blurred.The Raio Museum warns do not touch letters, i was using slightly damp towel just around them and just so lightly touched them they start to melt. So I warn you all if your ever get one of these just clean around the numerals and print. Resist. I can get a repro if I want, we'll see. 

kudos to GE, it is nice to have a slip connector on the antenna back as opposed to hard wiring, easy to slip out. Looks like a good player and despite the glass issue I will get this to play safely, GE did a good job on this little guy.

If you had one of these appreciate your thoughts. 

https://www.radiomuseum.org/r/general_el_200.html

Paul

Tubetalk1
#2

Paul I have a 201, very similar only it's in an ivory cabinet. It's a fairly decent player. Has an RF stage but not tuned RF.

Ron

Bendix 0626.      RCA 8BX5.   RCA T64
Philco 41-250.    Philco49-500
GE 201.             Philco 39-25
Motorola 61X13. Philco 46-42        Crosley 52TQ
Philco 37-116.    Philco 70
AK 35                Philco 46-350
Philco 620B.       Zenith Transoceanic B-600
Philco 60B.         Majestic 50
Philco 52-944.    AK 84




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently no members online.

>