Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60F for $20? Should I buy?
#1

Inspected the radio today...tubes all there, speaker in good condition, minor veneer damage. What's the catch?


Attached Files Image(s)
   
#2

If the tubes are in there, those alone are probably worth more than $20. If I had the space, and the time to tackle it, I would jump on this in a heartbeat. But I'm on the West Coast, where everyone thinks something like this is worth 5x what your price is. Icon_crazy

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#3

It's kind of amazing to find something like this in Phoenix. I've just got to figure where to put in...
#4

I guess the catch should be if the tubes are good, then they alone could be worth $20, at retail, but used 6.3 volt tubes are usually not that expensive unless it's an uncommon power triode like a 6A3. The model 60s used what I would call a pre-octal version of an AC AA5, 6A7, #78, #75, #42, and an #80. They are very straightforward sets, as far as Philcos go, but on some sets the police band portion of the oscillator coil will need rewinding, which is very easy to do. Other then that you need to check the big things, like the power transformer, the speaker field coil, and the output transformer, but those rarely fail unless a filter cap shorts out. I think for $20, if you have the room, and like the style of the cabinet, then why not?
Regards
Arran
#5

$20.00 Why not! Save it from the scrap heap! The tubes and speaker have to be worth that alone.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently 786 online users. [Complete List]
» 1 Member(s) | 785 Guest(s)
Avatar

>