Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Neutrowound Replacement Caps/Shields
#1

https://www.russoldradios.com/blog


In between smoke, fires, heat and a million other projects - -
Making replacement caps for a 1926 Neutrowound receiver.

Russ

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#2

Another impossible job made possible.
Icon_clap Icon_clap Icon_clap
Looks exactly like the original...super work!
#3

Very impressive Russ Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

Copy of post on WOOF Forum - - -

"After" picture added.

How thick? Well, that will vary a little and trimming of the flashing will cause a bit of variation at the base. I was aiming for a match to the original and without a micrometer measurement, they appear to be similar in thickness and strength ( I just inserted them into the radio and one was tight). The nickel could make them thicker (and of course does) but there is no reason to plate on so much nickel that fit is a problem.

The copper solution is acid-copper (basically a PH negative solution of copper sulfate).

Russ

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#5

Most impressive, Russ!

I don't hold with furniture that talks.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
AC/DC Transformer-less Sets
Some of the original Edison DC generators were in use until the 1940s. The NYC subway and electrified Long Island Rail ...MrFixr55 — 09:39 AM
Samlex heavy-Duty bench supply filter question
I suggest sticking with the original values. Depending upon the design if you increase the cap values too much the incre...DaleHCook — 08:55 AM
AC/DC Transformer-less Sets
You’re welcome! I was born in 1995, so this is all second-hand information to me from the industry. I did some research ...jrblasde — 08:38 AM
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM

[-]
Who's Online
There are currently 7268 online users. [Complete List]
» 3 Member(s) | 7265 Guest(s)
AvatarAvatarAvatar

>