Posts: 4,382
Threads: 412
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
As some may know the New England Vintage Electronics Club had our meet today in New Hampshire, though the morning looked promising a very pretty Sunrise the day was cool and overcast for the meet. Despite that many tailgated their wares and we had good crowds in the hall and in the Parking lot tailgating area. I think the tailgating is getting more popular due to not having to haul your goods all the way from lot to the hall just set up by your car, van, etc..... A high light was when of our members flew over several times in a Helicopter quite low at times to film the overhead view of the event, perhaps I can post when available.
At the meet a senior club member and a true gentleman in the hobby approached me with a FADA 195 A from the early 20's? Asking my help in locating a schematic, I have looked on line but no luck. We did meet another fellow a NJARC member who had worked on that set some time ago and offered some pointers, but also said he could not find a schematic.
So to these in this esteemed group, can any one render some assistance?
I am much obliged.
Paul
Tubetalk1
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
cant help here have lot of fada schematic's but nothing on 195a
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,382
Threads: 412
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
Thanks Sam, it is an oldie, way back machine.
Paul
Tubetalk1
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Paul;
I have a Fada 175A, and I could not find a factory diagram for it either, but I found one that someone had made by tracing out the wiring in the set, in my case it was a 1924 model. One way you can often tell is that 1924-25 and earlier sets will have UV bayonet style sockets, but the 1925-26 and newer models will have UX style four pin style.
The 192A was also known as the "Neutrolette", which I think was intended to be an economy model, unlike the Fada 175A there is a diagram in either the first Riders volume, or in one of the Gernsback books, it's a 1925 model. Five will get you ten that one or both of the audio interstage transformers are open circuit, my 175A still has the originals, one is good but the other is open circuit on one winding. Here is a site that has some of Gernsback;s books posted, as well as lots of early radio books and magazines, if you want to look:
https://www.americanradiohistory.com/
Regards
Arran
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
arran
here is a copy of 175 same as 185
https://documentcloud.adobe.com/link/tra...f428ea762b
lol ok so it copied whole section 175 is 13-10
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Sam;
Those are at least a decade newer, my 175A is a three dial TRF from 1924, it's from the original F.A.D.Andrea company, before Frank sold the company.
Regards
Arran
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Philco 60 Squealing
|
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM |
Philco 60 Squealing
|
I just peaked it for the best signal at 600.
NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM |
Philco 60 Squealing
|
Wavetrap no longer matters.morzh — 05:19 PM |
Philco 60 Squealing
|
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM |
37-690 Bass Choke Replacement
|
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM |
37-690 Bass Choke Replacement
|
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM |
37-690 Bass Choke Replacement
|
Ah, now where to find one.
I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM |
Philco 38-7 Speaker
|
Ask the admins to put them together.
As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM |
37-690 Bass Choke Replacement
|
This is the parts catalog.
32-7528 choke is 65H, 10mA, 2,250 Ohm inductance.
Find a suitable one.morzh — 02:18 PM |
37-690 Bass Choke Replacement
|
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM |
Who's Online
|
There are currently 3801 online users. [Complete List] » 1 Member(s) | 3800 Guest(s)
|
|
|
|