1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 45F tuning capacitor sub-chassis sloppiness
49Stude63
Member
***
Posts: 225
Threads: 14
Joined: Oct 2005
City: Grand Blanc, Michigan
#1

02-06-2006, 05:35 PM
On my 45F the tuning capacitor sub-chassis is mounted onto the main chassis by 4 bolts. I just finished re-capping the paper caps and bakelite blocks and waiting for the odd ball 6 uf electrolytic to show up at the moment. While I was doing the re-cap I noticed the tuning capacitor sub-chassis is loose and sloppy, the rubber insulators are still intact top and bottom but they must have shrunk with age and caused the looseness. Can I just use faucet washers to shim the subchassis tight near all 4 mounting bolts or should I dis-mantle and make new insulators for each mounting bolt?
Find
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#2

02-06-2006, 06:09 PM
Try using the replacement chassis gum washers being offered by some vendors. Might be a cut-N-fit but may get you close? Also regular black rubber grommets of correct size to suit?
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
49Stude63
Member
***
Posts: 225
Threads: 14
Joined: Oct 2005
City: Grand Blanc, Michigan
#3

02-08-2006, 04:29 PM
Chuck I used the faucet washers and it worked great. Nice and snug and not that hard to do. Icon_eek Soon as I get the 6 mfd and 2 8mfd electrolytics and one 250pf mica (bad) it will be all done and ready to go. Hopefully it actually plays.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 4255 online users. [Complete List]
» 1 Member(s) | 4254 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration