Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
I picked up this 1935 RCA tombstone at the last WARCI meet on September 16. It was only $20 so I figured what the heck, I'll give it a shot. Once I was able to get the radio playing again after a complete recap, some resistor replacements and two tubes, I knew I had to tackle the cabinet. Needless to say, it was a real veneer replacement challenge, but all in all I think it turned out fairly well. Far from perfect but a whole lot better than it was. 
Before:
After:
Before:
After:
Greg V.
West Bend, WI
Member WARCI.org
Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
Greg V.
West Bend, WI
Member WARCI.org
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Beautiful work Greg. I think you did an excellent job on the veneer replacement.
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Very nice work.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Greg,
You did a great job!
--
Ron Ramirez
Ferdinand IN
Posts: 1,463
Threads: 97
Joined: Jul 2012
City: Poughkeepsie, N.Y.
Greg super job!!! You saved it to be played again... And we thank you for that.
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
Nice save Greg
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA
State, Province, Country: California
Very nice, Greg!! Nice to see a near junker pulled away from the flames!
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
Fantastic workmanship,,,,,
Posts: 1,287
Threads: 44
Joined: Nov 2017
City: Menlo Park
State, Province, Country: CA
Very nice work!
I don't hold with furniture that talks.
Posts: 56
Threads: 9
Joined: Nov 2018
City: Rosthern
State, Province, Country: Saskatchewan, Canada
Looks fantastic perhaps better than new?
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
>>but a whole lot better than it was.
You said it, brother!
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 461
Threads: 31
Joined: Sep 2009
City: Lapeer
State, Province, Country: MI
A real beauty. Great work! 
Joe
Matthew 16:26 "For what does it profit a man if he gain the whole world, yet lose his own soul?"
Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
Thanks, everyone. It was definitely a challenge!
Greg V.
West Bend, WI
Member WARCI.org
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Philco 46-420 Code 121 Reception issues
|
| Welcome Eric,
I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM |
|
Philco 46-420 Code 121 Reception issues
|
| You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM |
|
Philco 42-1008 conversion kit
|
| Interesting. I haven't seen that before.klondike98 — 07:02 PM |
|
12' Philco
|
| Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM |
|
Shadow Meter Bulb
|
| Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM |
|
Shadow Meter Bulb
|
| Ok. Thanks for the correction.RossH — 03:09 PM |
|
Model 28L
|
| For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM |
|
37-60 revision 6
|
| I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM |
|
Shadow Meter Bulb
|
| Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM |
|
Hickok AC51 tube tester
|
| Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
|
Who's Online
|
There are currently 3237 online users. [Complete List]
» 1 Member(s) | 3236 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
