1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Filament Resistor replacement
elfiself
Member
***
Posts: 58
Threads: 9
Joined: Apr 2016
City: Albany,NY
#1

11-23-2018, 01:45 PM
Half of a 33-3408-3 filament resistor is bad and I'm looking to replace the whole component. It is a 40/80 ohm. what wattage value would be appropriate?
TIA
elfiself
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#2

11-23-2018, 02:41 PM
Actual dissipation is abt 3W BUT if you don't want a flaming hot resistor go w/abt X3= 7-10W.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
morzh
Odobenus rosmarus
******
Posts: 16,579
Threads: 574
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#3

11-23-2018, 03:35 PM
For power resistors I triple the ating, so for 3W it is 10W for me.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
elfiself
Member
***
Posts: 58
Threads: 9
Joined: Apr 2016
City: Albany,NY
#4

11-23-2018, 04:51 PM
Thanks Terry. The math works out to 2.4W X3 Looks like 10W should cover it.
Larry
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum! :wave: Here's the schematic for that radio from our digital library: Something to do bef...klondike98 — 08:05 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration