1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Grunow 654.. No Audio
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#1

11-28-2018, 06:04 PM
Just recapped.. turned on and at 100 Volts in draws 400 Ma..

B+ to ground is approx 310 Volts DC..

No audio.. When turning volume up and down get scratches.. No noticeable Hum..

Can scan schematic . Replaced the Bias cell with Watch battery.. Plus to Ground..

Skip
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#2

11-28-2018, 06:28 PM
OK Here are schematics..


[Image: https://farm5.staticflickr.com/4843/4518...c178_b.jpg]

[Image: https://farm5.staticflickr.com/4822/4518...af0e_b.jpg]


[Image: https://farm5.staticflickr.com/4828/4518...ee59_b.jpg]


OK  On second picture  The Black and Yellow leads were reversed.. I put them to match the schematic so the Resistance of field coil would be right.. Did I goof???

Skip
(This post was last modified: 11-28-2018, 06:30 PM by vecher.)
Find
morzh
Odobenus rosmarus
*****
Posts: 15,704
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
#3

11-29-2018, 03:02 PM
When touching 2nd det cap or the output tube's grid, is there hum?
Are there voltages on plates?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 11-29-2018, 03:06 PM by morzh.)
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#4

11-29-2018, 05:05 PM
Ok  Stupid mistake again.. I forgot to install a resistor.. No voltage to OSC.. After install worked correctly..

Next Question  Where is the best spot to hook up my VTVM to measure the AVC Voltage?  Cannot get yo speaker voice coil to put on my output meter..

Skip
(This post was last modified: 11-29-2018, 05:06 PM by vecher.)
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1748 online users. [Complete List]
» 1 Member(s) | 1747 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)