Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Caps for Eico 460 Scope
#1

Hey guys, I'm going to recap my Eico 460 oscilloscope, and I cannot find a suitable replacement for these three .1mfd 2000 volt capacitors. Any idea of where I can get them or another way to accomplish the same thing?

   

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#2

Just Radios has some 0.1uF 2000v caps for $4.49 ea.  See: https://www.justradios.com/cart.html and do a "Find 2000v" in your browser.  its buried in the listing. You will get 2 hits on "2000v" a 1uF and a 0.1uF.

I would guess Mouser would have some as well but I did not look.
#3

Thanks Bob, I went to Just Radios and looked, prior to my post, but I must have missed it. My wife says I do that a lot, especially when I tell her something is not in the refrigerator when she ask me to get her something!  Icon_rolleyes I greatly appreciate it!

Gregg

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#4

Unless they are leaking why replace? Confirmation of leaking is the in-ability to center the trace vertical/horizontal. Replacement may not have the rise time, could effect the top operating frequency.

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#5

Since I’m working on this scope I was thinking about adding a grounded power cord with grounding to the chassis. Any thoughts on this? Good idea, bad idea? What say you?

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#6

If it doen't have it now, don't...

I cut the ground of my vintage Dumont and of my BK desktop DVM. Too many accidental shorts to hot projects...

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>