Posts: 1,189
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Posts: 1,189
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
That is quite a cabinet. The finish appears to have yellowed. If it were to be refinished it would look amazing, BUT, it is also too nice to refinish. It is possible that the hand-cleaner method might help remove some of the "yellow".
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 12-12-2018, 11:57 AM by Phlogiston.)
Posts: 1,189
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Russ, at some point in it's history, someone tried to "restore" the finish. If you look at the edge of the door, you can see where something was wiped on and slightly spread over onto the inside surface of the door. There is evidence of this in multiple places. Perhaps you are familiar with what might have been used??? The inside of the doors and the speaker grill have a very strange color and are probably the original, deteriorated finish. The inside of the record player compartment is probably close to the original walnut color on the cabinet. Much more brown. Looking at the inside of the doors and the grille, what kind of finish would have deteriorated in that way? It looks highly oxidized and almost greenish in color. Could they have used shellac instead of lacquer? Does shellac age in that way?
It looks quite nice just sitting there and I may just leave it. It would be a lot of work to refinish and, perhaps, beyond my skill level. I would probably send it to a local pro who does a lot of refinishing of locally made, fine furniture from the earlier part of last century during Grand Rapid's heyday of furniture manufacturing. My Grebe cabinet was made by the same comapny - Berkey and Gay. I just recently discovered that quite by accident and that added to my interest in the Grebe and in this Balkeit. I like the local history, even if the radios themselves were made elsewhere and may be of questionable performance. Interstingly, I would say Berkey and Gay built the Grebe cabinet down to a price as I didn't think the construction was all that high a quality. The Balkeit seems to be a much finer cabinet. For me, it may be worth spend the $$$ on getting it refinished just for my personal satisfaction. I'm thinking out loud here and convincing myself to have it refinished!
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Yes, shellac can turn black, green or white with age and moisture but so can lacquer.
Here is a Wurlitzer that turned white:
Your radio could have been finished in shellac or lacquer. It looks like somebody tried to brighten up the yellowed finish. This would be justification (for me) to refinish it. It will be an awesome cabinet if done properly. You can test for shellac in a hidden area by applying alcohol on a rag to see if the old finish will dissolve and lacquer thinner to see if that "top coat" is poly which will get soft, but not wipe off. Hope it is not poly.
Be careful with the solvents.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 1,189
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Boy, I hope it's not poly as well! I may test it as you suggested.
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
I was looking at an old catalog from the early 1930s, and they had a number of sets with cabinets made by Berkey and Gay Furniture, one of the makes was something called a "Cadillac" which I have never heard of, it may have been a private label brand, or the mail order outfit may have assembled them using surplus chassis installed into B&G cabinets. Balkeit was one of the larger independents started in the 1920s, whom had a few good years during the radio boom, then slowly faded, then went bust or merged into another firm.
Regards
Arran
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
12' Philco
|
GarySP — 01:17 PM |
Hickok AC51 tube tester
|
I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
IF can wire size and Rubber mounts?
|
Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
12' Philco
|
Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
Hickok AC51 tube tester
|
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
IF can wire size and Rubber mounts?
|
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
Hickok AC51 tube tester
|
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM |
IF can wire size and Rubber mounts?
|
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM |
My last cabinet for this year
|
Hello Dan,
That is really beautiful what great looking radio you have !
I have friends who live in Calgary and the wea...radiorich — 01:51 AM |
Philco Predicta Siesta picture over time getting dimmer
|
I found that the wire insulation was burnt.
The fly back needs corona dope!
Why would someone put that there?Platinumblonde36 — 01:09 AM |
Who's Online
|
There are currently 5138 online users. [Complete List] » 1 Member(s) | 5137 Guest(s)
|
|
|
|