Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith MJ1035, is it worth looking for one?
#1

While sitting in the house avoiding the dropping temps and grumping at the lake effect snow, I got to thinking about this table radio from Zenith. I almost had one of these last fall, but the guy was rather rude and I just wasn't in the mood for it, so I let him pound sand. Now, are these good radios if found complete with their external speaker? I have a similar unit offered by Silvertone that uses a similar set up, but has 14 tubes crammed into it and push-pull output on both sides. The downside is the fact that they only use one 6 inch speaker in the radio and the external speaker unlike the bigger speakers and the tweeters that Zenith used. (Still plan to get it repaired someday.) I also like the looks of the Zenith and always considered this model to be the king of their AM-FM table radio line. So, would one of these be really worth looking for once the weather eases up (noting the frustrations of finding things in Ohio and finding them complete and at reasonable cost), or should I just stick with my C845Y? Icon_smile

No matter where you go, there you are.
#2

I would not bust a gut to get one...................if you have several good Zeniths...............

Paul

Tubetalk1
#3

They are supposed to sound pretty good, but on the expensive side when it's both the radio and extension speaker.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

I'd say stick with what you've got.
#5

Best I remember they are series string & have a single ended 35C5 amp for each channel.

There's AM/FM Stereo RCA of similar size with remote speaker that is transformer powered and uses single ended 6BQ5 in amps.

Model is something like 4RC96 or at least similar.

Well dayum, I 'membered the model.

https://www.radiomuseum.org/r/rca_4rc96.html

Tom




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM
Zenith H725
I think the problem is traced - to noise on the AC line. It sounded so local, that it seemed certain it was generated wi...EdHolland — 05:51 PM

[-]
Who's Online
There are currently 928 online users. [Complete List]
» 1 Member(s) | 927 Guest(s)
Avatar

>