Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hallicrafters Model S-107
#1

My wife's nephew came by last night and brought me a couple of items. He sometimes comes across stuff he thinks I might like. The first one is a Hallicrafters Model S-107 Radio/Receiver. I know nothing about this, bit it looks to be in fairly nice condition. It definitely needs cleaning and probably recapping, but the power cord seems very flexible. I did plug it in and had dial lights and a very quiet hum. Can anyone tell me anything about this? I see it has antenna screws in the back, two with metal jumper. I also saw a little rubber grommet on the top rear of the cabinet, don't know what that is for? Anyway, I'll post a couple of pictures later when I'm at my computer. He also brought me a really clean VOM. It's a RCA model WY- something or other. I checked it out after he left and found all it needed was a new electrolytic cap, the pots. cleaned, and the wafer switches cleaned and DeOxit'd. Once I did those, it was working perfectly! It even came with all three leads! Now I can add it to my stable of restored diagnostic tools. I'll post a couple pics of that too. Currently waiting for four new tires to be installed on my truck.

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#2

its apparently not a bad set.. but am no expert.

i hare restored a half dozen hallicrafters from s38 to s53.

lookie there
http://wd4eui.com/Hallicrafters_S_107.html

the shorting is disabled if you use a long wire to terminal 1.

,, not sure on the rubber grommet.

i actually can appreciate how it extracts out the front instead of the rear.
#3

Nice set Tubes are fairly common. On the back if the jumper is connected to ground it is set up to use a single piece of wire as a ant. You can remove the jumper and use twin lead to hookup a dipole ant.Back on June 06 2015 I posted a pdf for the S38E the ant hookup would be the same. Enjoy your new set.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3497 online users. [Complete List]
» 2 Member(s) | 3495 Guest(s)
AvatarAvatar

>