1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Canadian Model chassis 66? Ideas?
shawn1967
Junior Member
**
Posts: 12
Threads: 5
Joined: May 2018
City: Phoenix, AZ
#1

03-10-2019, 06:17 PM
Am helping a family on Cave Creek Az prepare father's collection of Philco radios for sale. Any Ideas on the specifics of this Philco Canada postwar model? Thanks!


Attached Files Image(s)
           
Find
Arran
Phorum Expert
*****
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

03-11-2019, 04:06 AM
It's basically like a pre war 42-327, but it's post war, with a different dial, post war knobs, and minimal rubber/gutta percha wire (if any).I don't think they are terribly valuable, but they are good performers, with two IF amplifier stages, I think, six tube AC/DC set. The dial looks like the paint is lifting off the back, so beware, hopefully it's just dirt on the front. Whoever brought it to Arizona likely brought it from Southern Ontario judging by the call letters, CHUM is in Toronto.
Regards
Arran
(This post was last modified: 03-11-2019, 04:10 AM by Arran.)
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3609 online users. [Complete List]
» 2 Member(s) | 3607 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios