1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco Model 90 Tuning Dial
Jonathan Philco 41
New Member
*
Posts: 2
Threads: 1
Joined: Apr 2019
City: Huntsville State, Province, Country: Alabama
#1

04-05-2019, 09:37 AM
Hello friends. I just restored a Philco model 90. Turned out great. As with many of these, the tuning knob/dial slips when tuning. It turns but the dial does not. does anybody have any suggestions on how to fix this tuning bushing or where to obtain a new one?  Thank you.

Jon
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

04-05-2019, 10:09 PM
Hi Jon and welcome,
Would have replied sooner  but it's been along time since I've serviced a model 90. So what's the problem? Is the tuning shaft pinching the inside of the dial hub correctly?? Is the tuning shaft worn badly so pinching mechanism can't grip the hub. Spring weak?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Jonathan Philco 41
New Member
*
Posts: 2
Threads: 1
Joined: Apr 2019
City: Huntsville State, Province, Country: Alabama
#3

04-09-2019, 05:41 PM
Hi Terry . Sorry for the late reply. The radio is put back together. I can tune the radio if I push down on the tuning knob as I turn the tuning knob. I have two model 90's with the same problem. One is worse than the other however. It is irritating indeed. The restore turned out excellent however. Could you send me a private message so I can send you my contact information?
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4034 online users. [Complete List]
» 3 Member(s) | 4031 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios