1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 38-690 Volume Control Removal
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#1

05-01-2019, 06:24 PM
I was able to remove the control shaft easily. I was going to remove the rear apron but
it is riveted on the left end looking at the bottom. What is the best approach for removing
the volume control for replacement?

Thanks,
nv3g
Oscar
(This post was last modified: 05-03-2019, 12:15 PM by NV3G.)
Find
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#2

05-01-2019, 07:30 PM
Oscar

It's been two years since I stared mine (Iasted me all summer) so I'm not fresh on it: aren't the pots there being held by nuts?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#3

05-01-2019, 09:55 PM
If you are talking about disassembling the vol pot it's self - don't. Just figure out a way to get a little de-oxit (green label) into the pot - a little.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#4

05-02-2019, 07:53 AM
I recently bought the Trolmaster pump - if you could find one, this is exactly what you need. You will probably still have to unscrew the pot - I am not sure the Trolmaster would fit in there or go through the front.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently 2135 online users. [Complete List]
» 1 Member(s) | 2134 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration