Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What do I have here?
#1

I purchased this at an estate sale with no accompanying information. The tube chassis has stamped “D 14170”. Is that the model #?

Mark W
#2

Welcome to the Phorum!

That's not a model number - more likely a serial number.

Info here on identifying Philco radios:
https://philcoradio.com/library/index.ph...ion-guide/

Alternatively post a few pictures and we can help.
#3

Welcome to the Phorum!
Icon_wave
#4

Hi could you tell me what replacement capacitor would I use for BR3045A 3 cap mfds volts 450 thank you James
#5

Hi James and welcome.
To answer your question I'll ask you a question, what Philco model are you servicing??
Part numbers are sometimes hard to sort out when you don't not know what they go to.

Not sure if the post goes w/the 1st three maybe Bob can move it and change it to a separate thread.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Any ideas on what model this is?


Attached Files Image(s)
               
#7

Looks like a 42-365K to me. The three tuning bands seem to match as does the cabinet.
#8

Thank you, Bob!
#9

We do not have a good photo of that model in our gallery. If you could take a few shots of it face on, it would make a nice addition. You can post it here or send it to Nathan Slingerland. Thanks much!!!
#10

More pics
#11

   
#12

Thanks!!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM

[-]
Who's Online
There are currently 3047 online users. [Complete List]
» 2 Member(s) | 3045 Guest(s)
AvatarAvatar

>