1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
VTVM how the heck do i use it?
jake wells
Still Learning.
***
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210 State, Province, Country: Kentucky
#1

06-29-2019, 12:20 AM
A elderly friend gifted me his restored heathkit lm-13 vtvm it needs a probe but my obvious question is can i use it like a regular volt/ohm meter or no?
(This post was last modified: 06-29-2019, 02:48 PM by jake wells.)
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

06-29-2019, 12:36 AM
http://tubularelectronics.com/Heath_Manu.../IM-13.pdf

You might want to check the battery, it's for the ohms measurement only. The probe for dc volts probably uses a 1 meg series resistor in it. To answer your question Yes. And it would be a Vacuum Tube Volt Ohm Meter vtvom.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
morzh
Odobenus rosmarus
*****
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
#3

06-29-2019, 01:08 PM
What the heck is VTVW? Or does W stand for M upside down?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment