Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I picked up this Opus 6 yesterday
#1

Talk about a sweet sounding radio.  Wow this thing sounds good. Superb reception as well.  Best I've had at my place where many of my other radios have trouble The cabinet is in excellent condition as are the glass knobs and buttons. 6 speakers, all working.  I've been on the hunt for a nice one for a long time. My search is done.


Attached Files Image(s)
       
#2

Them Germans built nice ones in 50s, yes. Any Telefunken is an excellent radio.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Just found one of these, will start restoring it soon. It is very nice condition but would like to recap it.

Jim
Spring Lake MI
#4

Jim please take lots of pics to share. David
#5

Will do.

Jim
Spring Lake MI
#6

At the very least I would want to replace the audio coupling capacitors, the tone correction cap on the primary of the output transformer (if it can one) and any bypass that runs between B+ and ground. A lot of West German radios used ERO brand capacitors, they are to German sets what Hunts are to British ones, replace on sight.
Regards
Arran
#7

Thank you Arran.
When I get started on this I will start a new thread.

Jim
Spring Lake MI
#8

Yes, my Grundig used ERO.....the worst I've seen so far. I keep them just so I could demonstrate how bad cap could drift. Up to 4 times up.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

Some tube-type and early solid-state Fishers also use ERO caps. The consensus seems to be divided on these as to replace vs. keep.

I replace them.

--
Ron Ramirez
Ferdinand IN
#10

Ron

when a cap goes up in value 4 times, to me there is no valid justification for leaving it in.
Out of all ERO caps in my radio (about 30+) there is no one single cap that did not go up at least 3x the value.
I think I might've even put a picture in my Grundig thread.
For comparison, all American caps in Philcos or Zeniths were 1.5x to 2x the value and in fact did work. Still needed to be replaced.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#11

No argument from me. Like I said...I replace them.

--
Ron Ramirez
Ferdinand IN
#12

https://philcoradio.com/phorum/showthrea...606&page=2

Actually, on this page I have the picture of 0.033uF cap measuring exactly 0.33uF.

Times 10.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#13

I was addressing the original poster in this, the set might work now, but it may not work a week from now, but replacing the audio coupling caps is the bare minimum someone should do.
Regards
Arran




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 3087 online users. [Complete List]
» 1 Member(s) | 3086 Guest(s)
Avatar

>