Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

NOOB here- how to set push buttons on model 39-45
#1

Hi everyone,  thanks for letting me join this site . When I was growing up in the 1950's my parents had a model 39-45 we listened to every day. Now here I am 65 years later and have finally finished its restoration. I'm trying to figure out how you set the push buttons. Does it require changes in the chassis or is there a way for the user to set them?  Also,  can I post a picture here?

Thanks,
Warren
#2

Hi and welcome,
The info the here in the service manual: http://www.nostalgiaair.org/Resources/298/M0013298.htm
There are two adjustments for each push button. One sets the osc and the other adjusts the ant circuit.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!

Yes you can post photos. See:
https://philcoradio.com/phorum/showthread.php?tid=29
#4

Welcome to the phorum!  Lots of very helpful pholks here to assist any way they can.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

Anyone know how or where to get new station labels?
#6

https://philcoradio.com/phorum/showthread.php?tid=5148

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM

[-]
Who's Online
There are currently 5748 online users. [Complete List]
» 1 Member(s) | 5747 Guest(s)
Avatar

>