Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

record plays at 78 but not 45
#1

Hello,

Just found a cool old 50-1721 in a basement.  I'd love to use it.  It gets a hum at high volume.  It turns but no sound unless its set at high rpm so you hear chipmunks but no sound at the correct speed.  Any ideas?

z
#2

Hi Zeb and welcome to the Phorum,
Several thing come to mind. Would service the chassis by testing tubes and resistors replace foil/paper caps along w/ eletrolyics. This will give you a good starting point to do any further troubleshooting.
The turntable give it a mechanical cleaning and lub. Not uncommon to find deteriorating rubber parts (driving the platen) that will need replacement. Another common issue is a weak cartridge (low output) and low tracking pressure.
After 69yrs these sets aren't a plug and play unit any more.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thank you very much... so far that is all a mystery to me so I'll start looking into how to do all that.  I'd love to get it working again.
#4

Whatchu got against chipmunks?!   Icon_lol
#5

Nothing really I just don't chipmunks in my vintage pre-chipmunk turntable
#6

Icon_lol    HA!   ok bud.
Terry is good , smart help.  There's lots of good help here.
#7

Nah just don't have a life.[Image: https://philcoradio.com/phorum/images/sm...on_lol.gif]

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>