Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help looking for a grill cloth
#1

        [attachment=20169]

I'm looking for a replacement grill cloth for my Philco Lowboy Model 89. If anyone has suggestions for vendors, I'd appreciate the help. Attached is a photo of the original and it's unique design. Thanks in advance. Denny
#2

Hi,

I dont think you are going to find an exact match, but here are two which are close:

https://www.ebay.com/itm/183963337703

https://www.ebay.com/itm/173864021931

--
Ron Ramirez
Ferdinand IN
#3

Hello Ron, Thanks for your help, the first eBay listing looks very similar. I'll check it out. Thanks again, Denny
#4

I wonder if that is the original cloth that came on the 89 B as well. Icon_question
#5

Hi Jake, I doubt if the grill cloth is the same on the lowboy and the cathedral. The reason I say that is because if you google the 89B you'll see that most of them have a very fine pattern in a light gold cloth. One of the best photos is here on this site. The grill cloth off my 89 lowboy, which I believe was original, is more of a herringbone design much like the one Ron pointed out for sale on eBay, earlier in this thread. Denny
#6

It isn't.

There are several different versions of the 89B.

https://philcoradio.com/library/index.ph...-model-89/

The first three cathedral cabinets shown use what is commonly known as "70/90" grille cloth because it is the same pattern used in model 70 and 90 cathedrals.

Exact duplicates of this cloth are no longer available. Close substitutes:

http://www.radiodaze.com/grille-cloth-02-item-grc02/
https://www.ebay.com/itm/183963258584

The June 1934 version used a diamond pattern similar to this:

http://www.radiodaze.com/grille-cloth-05-item-grc05/

Note that the green stripes should be vertical, not horizontal.

And the final version (January 1936) used what is commonly known as "Ribbed" cloth. A close substitute:

http://www.radiodaze.com/grille-cloth-14-item-grc14/

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3620 online users. [Complete List]
» 2 Member(s) | 3618 Guest(s)
AvatarAvatar

>