Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Exact resistor values.
#1

One little problem that irritates me to no end is when a radio calls for a certain part value and it is not available from my sources i use. Take for example my 38-62 two resistor values it calls for is 51K and 70K that is fine but all i can find is 47K and 68K. Not so good being able to find and use the right value would be nice instead throwing something together that is exact value.

End of rant off my soap box now Icon_neutral .
#2

51K is a standard value, you should have no trouble finding them. For the 70K, the best you can do is the 68K.

Steve

M R Radios   C M Tubes
#3

...and you can use a 47K to replace a 51K. 47K is less than 10% less than 51000 ohms. In ye olden days 20% tolerances were the norm...which meant anything from 40,800 to 61,200 ohms was considered "acceptable".

--
Ron Ramirez
Ferdinand IN
#4

Anyone know a good site for resistors and capacitors besides aes and justradios?
#5

Jake try Mouser.   https://www.mouser.com/Passive-Component...?P=1z0x74g
#6

Also for capacitors, resistors and much more, don't forget Sal's Capacitor Corner.

http://tuberadios.com/capacitors/

--
Ron Ramirez
Ferdinand IN
#7

Yep just ordered from Sal this past Wednesday, great prices!

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#8

Thanks for all suggestions guys. i did find 51k but not in metal film only in carbon film which is fine.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2980 online users. [Complete List]
» 3 Member(s) | 2977 Guest(s)
AvatarAvatarAvatar

>