Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric 202 revived.
#16

So it really only juices up signal going to output? Not really making it more sensitive? Paul

Tubetalk1
#17

It's still a solid little radio from GE and as far as I can tell, is at least a little more sensitive than my comparable five tube radios from the same time period. I get it about the styling as it is different. I wasn't really into this model either until someone here mentioned that they are good performers. Usually these are beat up or high priced around my area, but this one was a bargain flea market find this past summer. Icon_wink

No matter where you go, there you are.
#18

Just a guess on my part, but I'd guess that while the set is more sensitive than an AA5, it likely is not more selective. Have a look at the 1950 Philco model 50-921, for a very good sounding, super sensitive and selective bakelite table model that has tuned a RF and a tuned mixer for two tuned RF stages versus one stage in most sets. It probably won't be cheap either, but I have owned one and used it, and they are very good performers in a package about the same size as the G.E.
#19

want a sensitive and selective set then look for a howard a300 .
#20

I am sure that GE 202 is a very nice sounding and sensitive set. I just found it odd that they'd add the extra tuned stage up front and not tune a stage that was already there.
#21

John that Philco sounds like a nice set to have around i will keep my eye open.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need Help to ID this radio 11 tube Philco
Yes the 16B as morzh pointed out. Specifically its the January 1935 model version of the 16B. There are a couple earli...klondike98 — 11:51 PM
48-482 rear panel help
Welcome to the Phorum, keithchip! How far you take a radio on cabinet restoration is a matter of personal preference. ...GarySP — 11:28 PM
48-482 rear panel help
I've recently finished the internal restoration of a locally purchased Philco 48-482. The cabinet is in ok shape except ...keithchip — 10:28 PM
Need Help to ID this radio 11 tube Philco
Welcome to the Phorum, Ken! Lots of help here for all of your restoration questions. Take care and BE HEALTHY! - Gar...GarySP — 07:59 PM
Need Help to ID this radio 11 tube Philco
Thank you. I went to your online library and found 2 schematics. I will download and compare to components!Ken D. — 06:31 PM
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM

[-]
Who's Online
There are currently no members online.

>