Opinions: Grill Cloth for 37-116 & 116B & 16B
Posts: 111
Threads: 24
Joined: Oct 2016
City: Whitehall PA
I'm planning on ordering grill cloth for a 37-116, a 116B and a 16B. I'm soliciting opinions.
I seem to have two choices, neither of which have I've seen in person:
1) https://www.radiodaze.com/grille-cloth-0...c03-18x25/
2) https://www.ebay.com/itm/Antique-Radio-S...3977291267
The 37-116 and 116B have the same grill cloth pattern. I'm leaning toward the Radio Daze cloth for these. I think I need three pieces of this to cover both radios. The 37-116 needs two (one for the center and one for the two sides).
For the 16B I'm thinking the 2nd one, Richmond Designs, the better match.
Just needs new grill cloth, good original finish. Needs electrical restoration. Number 1 in the queue...
Needs to be refinished and electrically restored. Maybe #2 in the queue...
Needs new veneer on top and sides and electrically restored. Maybe #40 in the queue...
Can't think of anything witty.
Greg O.
Whitehall, PA
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
In terms of color I think I agree with you.
Overall I like the Richmond Designs chevron cloth a bit better. I found the texture and sheen was a closer match to the original than the RadioDaze cloth - at least for my 29CSX:
[Image: https://live.staticflickr.com/65535/4905...1ddb_c.jpg]
The Radio Daze cloth looks good too (I used it on my 116X) - but is more of a matte sheen and a bit thicker:
[Image: https://live.staticflickr.com/4615/25974...ccd1_c.jpg]
Also just to throw it in - an earlier discussion about Philco chevron grille cloth:
https://philcoradio.com/phorum/showthread.php?tid=6245
Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Keep in mind that if you try to cover all three speaker cutouts with one piece of cloth - the 2 smaller areas, left and right, should have the chevron centered in the openings. I have never found a single piece that would accomplish that.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI
Correct Russ. I made frames out of thin aluminum and attached the cloth to them for the 2 small openings. These were fastened to the inside of the cabinet before the sound board was installed.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
That cloth is darker/lighter depending on the viewing angle and the angle of the light source. So it is hard to compare.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 111
Threads: 24
Joined: Oct 2016
City: Whitehall PA
OK
If I assume the unexposed portion of old cloth is the original color, then the Richmond cloth is, as far as I can tell from the photos, a closer match in color, texture and sheen. Radio Daze seems to have matched to the color of the aged cloth. Still to me Radio Daze is a closer match since I've never seen a new 37-116.
Both clothes are "inverted" versions of the original, dark undivided stripe and a light divided stripe.
Maybe I'll flip a coin. Neither would look awful.
Buy the way is there anything I should know about removing the speaker other than that it looks pretty heavy?
Can't think of anything witty.
Greg O.
Whitehall, PA
Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI
YES! There is a diffuser cone mounted to the sound board. If you are not careful, you can easily damage the speaker cone by hitting the diffuser in the removal process. Keep the speaker as far back from the sound board as possible as you move the speaker around the mounting board.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
You can damage it even if you are careful. As I recall, the chassis shelf and brace (back of cabinet) are such that pulling the speaker strait back is impossible. So you must tilt the speaker back on top or the bottom to clear the shelf. Make minimum movements on the X and Y axis (you have only about 4" of lateral and vert. space before the wooden cone impacts the paper cone).
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 12-29-2019, 01:15 PM by Phlogiston.)
Posts: 13
Threads: 0
Joined: Apr 2021
City: Seaford
State, Province, Country: New York
Hi guys. Michael Katz here. I just got in the cloth for the Philco 16B "V" pattern (finally!). Since I don't own any of the V pattern Philcos, I would need some guidance as to how big to cut the cloth, for the 2 sizes I think are needed for the various sets. I would need to cut it big enough to cover the opening plus maybe 1" additional on every side.
Will post all 5 of the new patterns on my website soon. Thanks.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Michael,
Thank you for continuing to make grille cloth available to us collectors!
I don't own a 37-116 (which would likely need the largest piece of cloth). Actually, I only have one Philco console that uses that pattern - it is a 37-675X De Luxe, and I'll be a customer when you're ready to sell the cloth. I can measure it either this evening or tomorrow (having a brief medical test this afternoon).
The cloth is also used in many Philco tombstone sets (16B, 116B, 660B, 650B, 640B, etc., etc.) which would necessitate a smaller cloth, of course.
Come on, guys, please measure the sound board of your 37-116 and other Philco models using this pattern and post the measurements here so Michael can see them.
Oh, and don't forget, Michael's website is:
https://www.radiogrillecloth.com/
--
Ron Ramirez
Ferdinand IN
Posts: 1,599
Threads: 101
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello Ron,
is that cloth used in Philco 610b I can see what size mine used.
Michael that is great news thank you for all your hard work !
I do have a Few Zenith radios like my model 715 and model 908 which will need new grille cloth .
Sincerely Richard
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
I don’t see it on his site yet
But I have a 37-116 but it’s in my ny home that’s 5 hr away
So if any one can give him measurements
I would appreciate it
I would buy 2 or 3 extra just for spare
Wife has mean cats
Sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 990
Threads: 40
Joined: Feb 2015
City: Roseville, MN
The board on my 650 console is 12-3/4" x 20-1/2".
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Think the set that uses the most is the 201X. Center section is 14"w x 23"L and two pieces 7"w x 22"L. But back to the question at hand.
1934 16B peaked top
10 3/4"w x 14"L
The 1936 116B early is pretty much the same size. The late '36 is smaller.
116X
12"w x 24"L center section and two 10"x10" for clairifers.
37-116X
18" w x 24" L center section and two 10"x10" for clairifers.
These are hard to measure as they are covered by another board that the speaker is mounted to. Can't really see it.
Generally these measurements are edge to edge.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Users browsing this thread: 9 Guest(s)
|
Recent Posts
|
Shadow Meter Bulb
|
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM |
Shadow Meter Bulb
|
Ok. Thanks for the correction.RossH — 03:09 PM |
Model 28L
|
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM |
37-60 revision 6
|
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM |
Shadow Meter Bulb
|
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM |
Hickok AC51 tube tester
|
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
Model 28L
|
Hello,
I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020.
Can...HORSTE — 10:32 AM |
Philco 42-1008 conversion kit
|
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM |
HiFi (Chifi) tube amp build - but my own design.
|
Tim
Well...a chassis is metal. Magnetic or not, it does not matter.
A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM |
Hickok AC51 tube tester
|
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM |
Who's Online
|
There are currently no members online. |
|
|