Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Hi, all. The primary on the RF coil is open. You will note on the 37-620 code 125, the BC transformer has only a secondary winding. The primary on the police/sw band coil apparently supplies the BC as well. So I am stuck about how to replace or repair this. I can find a replacement RF coil on AES, but that coil obviously has the primary and secondary together, not like it is on my Philco. Any ideas? Thanks. Mark
Posts: 5,060
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Welcome to the Phorum!
For those following along in this thread here's the link to the schematic: LINK
UPDATE: this link is for Code 121, the correct schematic is found below in Post #6
Posts: 658
Threads: 8
Joined: Apr 2018
City: S. Dartmouth
State, Province, Country: MA
I am referencing the schematic provided...
IMHO only a replacement (Philco) RF transformer for the BC band will be a drop in fit.
Alternately it can be rewound.
Although the schematic is just a line drawing of the RF coil, it appears to have a combination of solenoid and universal winds.
Stated, the primary is open, that could be the universal wind.
It is possible to scramble wind that primary as it is not tuned.
Scramble wind is a compromise, best advise is not to compromise on any other coil parameter such as the turns and wire size & type.
A Morris winder could reasonably replicate the universal wind...
GL
Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Ah, thanks for replying Chas, but can you translate that for me! I don't have any equipment for winding coils. Can you direct me to someone who can? Thanks. Mark
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Bob, the link to the schematic you included is not the code 125, so it is not the same as my radio. The earlier version 37-620 has a different RF transformer with primary and secondary coils. The code 125 has only a secondary coil.
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
![02-03-2020, 10:19 AM](attachment.php?aid=21493)
I am attaching a scan of my schematic since it is hard to find.
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
Hi MarkinK-Zoo,
Andy Sorrell and I have been building up the library of scanned service bulletins in the Philco Library.
Have a look here and enter `37-620` in the search box:
https://philcoradio.com/library/index.ph...bulletins/
Service bulletin 251A is for the 37-620 (Code 125).
Posts: 658
Threads: 8
Joined: Apr 2018
City: S. Dartmouth
State, Province, Country: MA
Quote:Ah, thanks for replying Chas, but can you translate that for me! I don't have any equipment for winding coils. Can you direct me to someone who can? Thanks. Mark
I do not know of someone who would wind or repair an RF coil as a hobby for others.
Post SHARP well lighted images of the defective coil. It will have to be removed from the radio.
Use colored pens or paints to mark the connecting wires. If you can find any other data on the chassis, occasionally, the coil will have a red or other bright color reference mark, record that to your notes...
When removing the coil for its photo session use great care not to disturb the wiring as little as possible.
Post the coil images, indicate your chassis variation, a WTB in the Phorum classifieds.
I'm sure that some collectors have coil "junk" boxes but may not know where the coil came from. So, comparison images will help.
A single, even a double layer solenoid wind for the BC band can be replicated by hand with no tooling.. Opps, will need a micrometer to measure the wire.
New supplies:
Wire, bees wax, >>>> patience... <<<<
GL
Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
(This post was last modified: 02-03-2020, 10:49 AM by Chas.)
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Chas: the schematic I posted is correct. The link to a schematic that Klondike98/Bob included is not correct. So, you hopefully you are able to see what you need on the image in my post. I would be willing to rewind the coil by hand, but measuring the gauge of the wire sounds like a challenge to me. I can buy a micrometer, but it all looks as fine as human hair to me and I can't imagine being able to tell the difference. Mark
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Nathan: Thanks for the link, but I have all of those pages. Years ago I ordered it from AES because I couldn't find a free download at the time. Mark
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
I have read about by-passing defective IF stages using a capacitor to connect the plate of one tube to the grid of the next and by-passing the open winding with a resistor. Would this work for an RF stage? There would be some loss of performance I would assume, but it would be way better than what I have now. Can this done? Mark
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Well, I think I answered my own question. I followed an article I had down loaded years ago about by-passing defective IF transformers and tried this with my defective RF transformer. The performance was worse. So I guess either finding a replacement (unlikely) or rewinding (not really wanting to do this!) are my only options.
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
MarkinK-zoo - I think I may have a 37-620 parts chassis. Will check tonight.
Posts: 15
Threads: 3
Joined: Feb 2020
City: KALAMAZOO
State, Province, Country: MI
Well, Nathan, wouldn't that be fantastic!
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
Sorry to say I checked and I don't have a 37-620 chassis.
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Cannot Adjust an IF Transformer’s cores
|
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM |
Cannot Adjust an IF Transformer’s cores
|
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM |
PT-6 antenna connections
|
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM |
Cannot Adjust an IF Transformer’s cores
|
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM |
PT-6 antenna connections
|
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM |
bridkarl
|
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM |
Cannot Adjust an IF Transformer’s cores
|
Joseph, now you are an engineer!!RodB — 06:37 PM |
PT-6 antenna connections
|
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM |
Cannot Adjust an IF Transformer’s cores
|
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
PT-6 antenna connections
|
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
Who's Online
|
There are currently 3531 online users. [Complete List] » 1 Member(s) | 3530 Guest(s)
|
|
|
![>](https://philcoradio.com/phorum/images/bootbb/asb/right_arrow.png)
|